SAMOTECH SM301Z Zigbeeモーションセンサー ユーザーマニュアル

1. はじめに

The SAMOTECH SM301Z is a Zigbee-enabled motion sensor designed to enhance your smart home system. It provides reliable motion detection, enabling automation routines for lighting, security, and other smart devices. This manual provides detailed instructions for setup, operation, and maintenance of your SM301Z motion sensor.

Image 1.1: SAMOTECH SM301Z Zigbee Motion Sensor and its packaging.

2. パッケージ内容

パッケージにすべてのアイテムが含まれていることを確認します。

• 1 x SAMOTECH SM301Z Zigbee Motion Sensor
• 単3電池XNUMX本
• 1×取り付け用接着剤

3. 仕様

4. セットアップとインストール

4.1. 重要な互換性に関する注意事項

The SAMOTECH SM301Z is a ジグビー device and requires a compatible Zigbee hub for operation. It is not a Wi-Fi device and cannot connect directly to your Wi-Fi network. Ensure you have a compatible Zigbee hub (e.g., Samotech SM310ZHA Hub, deCONZ, SmartThings, Hubitat Elevation, Home Assistant) before proceeding.

Image 4.1: The SM301Z requires a Zigbee hub and is not Wi-Fi compatible.

4.2. バッテリーの取り付け

1. Gently open the back cover of the motion sensor.
2. Insert the three AAA batteries into the battery compartment, ensuring correct polarity (+/-).
3. 裏蓋をしっかりと閉めてください。

4.3. Pairing with Your Zigbee Hub

Follow these general steps to pair your SM301Z sensor with your Zigbee hub. Specific steps may vary slightly depending on your hub's application:

1. Ensure your Zigbee hub is powered on and in pairing mode (refer to your hub's manual for specific instructions).
2. On the SM301Z sensor, locate the RESET button (usually a small pinhole button). Press and hold the RESET button for approximately 5 seconds until the LED indicator on the sensor begins to blink. This indicates the sensor is in pairing mode.


図4.2: 例ample of a pairing mode screen in a smart home application.

3. Within your Zigbee hub's application, initiate the device search or 'add subdevice' function.
4. The hub should discover the SM301Z sensor. Once detected, follow the on-screen prompts in your app to complete the pairing process.

Image 4.3: Confirmation of successful device addition in a smart home application.

4.4. センサーの取り付け

The SM301Z sensor is designed for wall mounting. Choose a location where motion detection is desired, keeping in mind the 3-meter maximum range.

1. 取り付け面が清潔で、乾燥しており、滑らかであることを確認してください。
2. Peel off the protective film from one side of the provided mounting adhesive.
3. Attach the adhesive firmly to the back of the sensor.
4. Peel off the remaining protective film from the adhesive and press the sensor firmly onto the desired wall location for at least 30 seconds.

Image 4.4: Steps for battery installation and applying the mounting adhesive.

5. 操作手順

Once successfully paired and mounted, the SAMOTECH SM301Z motion sensor will detect movement within its 3-meter range and communicate this information to your Zigbee hub.

5.1. モーション検出

The sensor uses Passive Infrared (PIR) technology to detect changes in infrared radiation caused by moving objects, such as people. When motion is detected, the sensor sends a signal to your Zigbee hub.

図5.1: 例ample of motion detection status in a smart home application.

5.2. Creating Smart Routines

Leverage your Zigbee hub's capabilities to create automated routines based on motion detection:

• Lighting Automation: Configure lights to turn on when motion is detected in a room and turn off after a set period of no motion.
• セキュリティ警告: Receive notifications on your smartphone if motion is detected when you are away from home.
• 省エネ: Automate devices to power down when no activity is detected.

Image 5.2: The SM301Z sensor can automate lighting based on motion detection.

6. メンテナンス

6.1. バッテリーの交換

The SM301Z sensor is designed for long battery life (3+ years). When the batteries are low, your Zigbee hub application may notify you. To replace the batteries:

1. Gently open the back cover of the motion sensor.
2. 古い単4電池を取り外します。
3. Insert three new AAA batteries, ensuring correct polarity (+/-).
4. 裏蓋をしっかりと閉めてください。
5. 古い電池は地域の規制に従って廃棄してください。

7。 トラブルシューティング

If you encounter issues with your SAMOTECH SM301Z motion sensor, refer to the following common problems and solutions:

• センサーがハブとペアリングされない:
  • Ensure your Zigbee hub is powered on and in pairing mode.
  • Verify the sensor's batteries are correctly installed and charged.
  • Perform a factory reset on the sensor by holding the RESET button for 5 seconds until the LED blinks, then attempt pairing again.
  • Ensure the sensor is within range of your Zigbee hub during pairing.
• No motion detected or inconsistent detection:
  • Check the sensor's placement. Ensure there are no obstructions blocking its field of view.
  • Verify the batteries are not depleted.
  • Confirm the sensor is still connected to your Zigbee hub in the app. If not, re-pair the device.
  • Avoid placing the sensor near heat sources (e.g., vents, direct sunlight) as these can cause false detections.
• 誤った動きの検出:
  • Review the sensor's placement to ensure it's not detecting pets, curtains moving in a draft, or reflections.
  • Ensure the sensor is not exposed to direct sunlight or strong drafts.

8. 安全情報

デバイスを安全に操作するために、以下の安全ガイドラインを読んで従ってください。

• このデバイスは屋内での使用のみを目的としています。
• デバイスを極端な温度、直射日光、高湿度にさらさないでください。
• デバイスを水やその他の液体から遠ざけてください。
• ご自身でデバイスの分解や修理を試みないでください。修理が必要な場合は、サポートにお問い合わせください。
• 電池は地域の規制に従って適切に廃棄してください。

9. 保証とサポート

The SAMOTECH SM301Z motion sensor comes with a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official SAMOTECH webサイト。

For technical support, troubleshooting assistance, or any questions regarding your product, please contact SAMOTECH customer service through their official channels.