DEVMO AMS1117-5.0 5V Step-Down Linear Voltage Regulator Module

1.製品オーバーview

The DEVMO AMS1117-5.0 is a compact step-down linear voltage regulator module designed to convert a higher DC input voltage (6V to 12V) into a stable 5.0V DC output. This module is suitable for various electronic projects, including those compatible with Arduino platforms, where a regulated 5V power supply is required from a higher voltag電子ソース。

主な機能は次のとおりです。

• 入力ボリュームtage範囲： 6V to 12V DC.
• 出力巻tage: Stable 5.0V DC.
• 最大出力電流: Up to 800mA with a 6V input, decreasing to 200mA with a 12V input, limited by internal power dissipation.
• 繋がり： Solderable pins for easy input and output connections.
• インジケータ： A PCB-mounted LED illuminates when voltage is applied to the module, indicating power status.

2. 仕様

2.1。 電気的仕様

Note: The maximum output current is limited by the regulator's internal power dissipation and decreases as the input voltage increases. The module cannot provide 800mA output at all input voltages。

2.2.物理的仕様

3. セットアップとインストール

This module is designed for easy integration into electronic circuits. Proper connection of input and output terminals is crucial for safe and correct operation.

Figure 1: Two DEVMO AMS1117-5.0 modules with included pin headers. The modules feature solder pads for input and output connections.

3.1。 接続手順

1. 端末を識別します: The module has clearly marked solder pads for input and output. Typically, these are labeled '+' and '-' for input, and 'OUT' or '5V' for output. Refer to the module's silkscreen for exact markings.
2. 入力接続: Connect your DC power source (6V to 12V) to the input terminals. Ensure correct polarity: positive (+) of the power source to the '+' terminal of the module, and negative (-) to the '-' terminal.
3. 出力接続: Connect your load (e.g., Arduino board, 5V sensor) to the output terminals. Ensure correct polarity: the 5V output from the module to the positive input of your load, and the ground of the module to the ground of your load.
4. はんだ付け: Use appropriate soldering techniques to securely attach wires or pin headers to the module's pads. Ensure strong, clean solder joints to prevent intermittent connections.
5. 電源インジケーター: Once power is applied to the input, the onboard LED should illuminate, indicating that the module is receiving power and attempting to regulate the voltage.

3.2. 安全上の注意

• Always verify input and output polarities before applying power to prevent damage to the module or connected devices.
• 最大入力容量を超えないでくださいtag12VDCのe。
• Ensure the total current drawn by your load does not exceed the module's maximum output current capacity for the given input voltage. Exceeding this limit can lead to overheating and damage.
• 出力端子の短絡を避けてください。
• Handle the module by its edges to avoid touching components, especially after operation, as it may be warm.

4. 操作

The AMS1117-5.0 module operates as a linear voltage regulator. It dissipates excess input voltage as heat to maintain a stable 5.0V output. This means that the higher the input voltage and the higher the output current, the more heat the module will generate.

• 電源オン: DCボリュームを適用tage within the 6V to 12V range to the input terminals. The onboard LED will light up.
• 巻tage出力： The module will provide a regulated 5.0V DC at its output terminals.
• 現在の制限: Be mindful of the current limitations. For example, with a 12V input, the maximum stable output current is approximately 200mA. If your load requires more current, consider using a lower input voltage (closer to 6V) or an alternative power regulation method.
• 熱管理: For continuous operation at higher input voltages and currents, ensure adequate ventilation around the module to dissipate heat.

5. メンテナンス

The DEVMO AMS1117-5.0 module is a solid-state electronic component and generally requires minimal maintenance. However, following these guidelines can help ensure its longevity and reliable performance:

• 清潔さ: Keep the module free from dust, dirt, and moisture. Use a soft, dry brush or compressed air to clean if necessary. Avoid using liquid cleaners.
• 環境条件: Operate the module within its specified temperature range. Avoid extreme heat, cold, or humidity.
• 物理検査: Periodically inspect solder joints and connections for any signs of corrosion or damage.
• ストレージ： When not in use, store the module in an anti-static bag in a dry, cool environment.

6。 トラブルシューティング

If you encounter issues with your DEVMO AMS1117-5.0 module, consider the following troubleshooting steps:

• 出力なしVoltage / LED Off:
  • 入力ボリュームかどうかを確認しますtage is within the 6V to 12V range.
  • Verify input polarity. Incorrect polarity will prevent operation and may damage the module.
  • Inspect all connections for loose wires or poor solder joints.
  • 電源が正しく機能していることを確認してください。
• 出力巻tage is Lower Than 5V:
  • Check if the load current exceeds the module's maximum capacity for the given input voltage. Reduce the load or use a lower input voltage.
  • 入力ボリュームを確認するtage is stable and not dropping under load.
  • The module might be overheating. Allow it to cool down and ensure proper ventilation.
• モジュールの過熱:
  • This is common for linear regulators when the voltage difference between input and output is large, and the current draw is high.
  • 入力音量を下げるtage if possible, or reduce the load current.
  • Ensure adequate airflow around the module.
• 断続動作:
  • Check for cold solder joints or loose connections.
  • Ensure the power source is stable and not fluctuating.

7. 保証とサポート

For warranty information, technical support, or further assistance with your DEVMO AMS1117-5.0 module, please refer to the seller's return policy or contact the DEVMO customer support directly through the platform where the product was purchased. Keep your purchase receipt or order details handy for faster service.

DEVMO is committed to providing quality electronic components. If you have any questions regarding the operation or integration of this module, do not hesitate to seek assistance.