1. はじめに
This manual provides detailed instructions for the installation, operation, and maintenance of your RGBZONE S3003 Standard RC Servo Motor. Please read this manual thoroughly before use to ensure proper function and longevity of the product. This servo is designed for use in various remote-controlled applications including smart cars, robots, boats, and helicopters.
2.製品オーバーview
2.1 主な特徴
- Sensitive and Quiet Operation: Designed for high efficiency, low noise, fast response, and low power consumption.
- 質の高い建設： Manufactured from durable plastic for stable performance and extended service life.
- 安定した構造: Engineered to ensure reliable operation under various conditions.
2.2 アプリケーション
The S3003 servo motor is compatible with a wide range of RC models, including Futaba, Hpi, and Tamiya RC cars, as well as model airplanes, boats, and robotic projects. Its standard size allows for direct replacement in many existing setups.
図1：例amples of S3003 servo motor applications in RC ships, model airplanes, robots, and toys.
2.3 箱の中身
Each package typically includes the following components:
- S3003 Servo Motor
- Various Servo Horns (e.g., star-shaped, cross-shaped, single-arm)
- 取り付けネジ
- ゴム製グロメット
- Brass Eyelets
Figure 2: Contents of a single S3003 servo motor package.
Note: Servo motors may come with different wire color combinations (e.g., Yellow-Brown-Red or Black-White-Red). Both configurations are functionally identical.
Figure 3: S3003 servo motors showing potential wire color variations.
3. 技術仕様
| パラメータ | 価値 |
|---|---|
| Stall Torque (4.8V) | 3.2 kg / cm |
| Stall Torque (6.0V) | 4.1 kg / cm |
| Operating Speed (4.8V) | 0.23秒/60° |
| Operating Speed (6.0V) | 0.19秒/60° |
| 営業巻tage | 4.8V～7.2V |
| 寸法（長さ×幅×高さ） | 40mm X 20mm X 38mm（1.57 "×0.78"×1.50 "） |
| 重さ | 約38g（1.34オンス） |
| 商品型番 | FB0037 |
| メーカー推奨年齢 | 8歳以上 |
Figure 4: S3003 servo motor dimensions.
4. インストールとセットアップ
4.1 コンポーネントの識別
Familiarize yourself with the servo motor and its accessories as shown in Figure 2. The servo motor has a three-wire connector for power and control, and an output shaft for attaching servo horns.
4.2 Mounting the Servo
- Identify a suitable mounting location in your RC model or project. Ensure there is enough clearance for the servo's movement and wiring.
- Place the rubber grommets into the mounting tabs of the servo.
- Insert the brass eyelets into the grommets.
- Secure the servo using the provided mounting screws, passing them through the eyelets and into the mounting surface. Do not overtighten the screws, as this can damage the servo casing or grommets.
4.3 Attaching Servo Horns
- Select the appropriate servo horn for your application.
- Align the servo horn with the splines on the servo output shaft.
- Gently press the servo horn onto the shaft.
- Secure the servo horn with the small screw provided, inserting it through the center of the horn into the servo shaft.
4.4 Connecting the Servo
- Connect the servo's three-wire connector to the appropriate channel on your receiver or control board.
- Ensure the polarity is correct: typically, the brown/black wire is ground, the red wire is positive voltage, and the orange/yellow/white wire is the signal line. Refer to your receiver/controller manual for specific pin assignments.
- Verify that the power supply to the receiver/controller is within the servo's operating voltage範囲（4.8V-7.2V）。
図5：例ample installation of S3003 servo motors in an RC car and a robot arm.
5. 操作手順
5.1 制御信号
The S3003 servo motor is controlled by a Pulse Width Modulation (PWM) signal. The pulse width determines the angular position of the servo. A typical pulse width range is 1000 to 2000 microseconds (µs), corresponding to a 0 to 180-degree rotation, though the exact range may vary slightly.
5.2初期テスト
- After installation and connection, power on your RC system (transmitter first, then receiver/model).
- Move the corresponding control stick or dial on your transmitter. Observe the servo's movement.
- Ensure the servo moves smoothly and to the full extent required for your application without binding or excessive force.
- Adjust endpoints or trim settings on your transmitter if necessary to prevent over-travel or mechanical strain on the servo.
6. メンテナンス
- クリーニング： Keep the servo free from dust, dirt, and moisture. Use a soft, dry cloth to clean the exterior. Avoid using solvents or harsh chemicals.
- 検査： Regularly check the servo's wiring for any signs of damage or fraying. Ensure all mounting screws and servo horn screws are secure.
- ストレージ： Store the servo in a cool, dry place away from direct sunlight and extreme temperatures.
- 過負荷を避ける: Do not subject the servo to loads exceeding its specified stall torque, as this can lead to damage or premature failure.
7。 トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| サーボが応答しない | Incorrect wiring, no power, faulty receiver/controller, damaged servo. | Check all connections for correct polarity and secure fit. Verify power supply to the receiver/controller. Test with a known working servo or channel. |
| 不規則またはぎくしゃくした動き | 干渉、バッテリー残量低下tage, faulty signal, mechanical binding. | Ensure sufficient battery power. Check for sources of electrical interference. Inspect mechanical linkages for obstructions. Re-check signal wire connection. |
| Servo makes buzzing noise but doesn't move | Mechanical obstruction, servo horn binding, servo overloaded. | Remove servo horn and test movement. Check for any physical obstructions preventing movement. Reduce load on the servo. |
| Servo overheats | Excessive load, continuous stall, incorrect voltage. | Reduce mechanical load. Ensure servo is not continuously stalled. Verify operating voltage は規定の範囲内にあります。 |
8. 保証とサポート
Warranty information for the RGBZONE S3003 servo motor is typically provided at the point of purchase or included with the product packaging. Please retain your proof of purchase for any warranty claims.
For technical support, troubleshooting assistance beyond this manual, or inquiries regarding product defects, please contact RGBZONE customer service through the retailer where the product was purchased or visit the official RGBZONE web連絡先情報のサイト。