ユーザーマニュアル

1. はじめに

This manual provides essential information for the safe and effective use of the Technical Precision Replacement Battery for GE FANUC CNC POWER MATE E systems. Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage.

2. 安全情報

常に以下の安全ガイドラインに従ってください。

• しないでください attempt to disassemble, open, or service the battery pack.
• しないでください 押しつぶしたり、穴を開けたり、外部接点をショートさせたり、火または水の中に廃棄したりしないでください。
• しないでください store above 60°C (140°F).
• 本製品専用のバッテリーパックのみと交換してください。
• New battery pack must be fully charged before use.
• Read instructions in operating guide to reduce risk of fire or burns before using the battery.
• お子様の手の届かない場所に保管してください。
• 使用済みバッテリーは、地域の規制に従って廃棄してください。

Failure to follow these instructions can result in fire, explosion, or other hazards.

3.製品オーバーview

This product is a high-quality replacement lithium-ion battery pack designed for use with GE FANUC CNC POWER MATE E systems. It provides reliable power for the specified equipment.

図3.1: フロント view of the Technical Precision replacement battery pack. This image shows the main body of the battery, which is cylindrical and blue, with a black label indicating "Lithium-ion Battery Pack," "3.0VDC," "2000mAh," and "6.0Wh." Red and black wires extend from one end, terminating in a brown plastic connector.

図3.2: 角度付き view of the replacement battery pack. This perspective highlights the battery's cylindrical shape and the label, which includes the "Cameron Sino" brand logo and warnings such as "CAUTION WARRANTY VOID IF LABEL IS REMOVED" and "ATTENTION! NEW BATTERY PACK MUST BE FULLY CHARGED BEFORE USE." The red and black wires and the brown connector are also visible.

図3.3: 後方 view of the replacement battery pack. This image displays the reverse side of the battery, showing additional warning labels and manufacturer information. Text visible includes "DO NOT CRUSH, PUNCTURE SHORT EXTERNAL CONTACTS OR DISPOSE OF IN FIRE OR WATER" and "DO NOT STORE ABOVE 60°C (140°F)." The wires and connector are also visible.

図3.4: 上から下への角度 view of the replacement battery pack. This view provides a clearer look at the label, including the "Model No.: CS-FNC10SL" and "Part No.: A98L-0031-0006" information, along with the rating details. The wires and connector are positioned to the left.

図3.5: 下から上への角度 view of the replacement battery pack. This image emphasizes the safety warnings printed on the battery's label, such as "DO NOT ATTEMPT TO DISASSEMBLE, OPEN OR SERVICE THE BATTERY PACK" and "REPLACE ONLY WITH THE BATTERY PACK DESIGNATED FOR THIS PRODUCT." The brown connector and wires are visible on the left.

4. セットアップとインストール

Before installing the new battery, ensure the GE FANUC CNC POWER MATE E system is powered off and disconnected from all power sources. Refer to your original equipment's service manual for specific battery replacement procedures.

1. 電源を切る： Completely shut down the CNC system and unplug it from the power outlet.
2. Locate Battery: Identify the location of the existing battery within the GE FANUC CNC POWER MATE E unit. This may require opening a service panel.
3. 古いバッテリーを取り外す: Carefully disconnect the old battery from its connector. Note the orientation of the connector to ensure correct installation of the new battery.
4. 古いバッテリーを取り外す: Gently remove the old battery from its housing or mounting.
5. 新しいバッテリーを取り付けます: Insert the new Technical Precision replacement battery into the designated slot or mounting area.
6. 新しいバッテリーを接続します: Connect the brown plastic connector of the new battery to the corresponding port on the CNC system. Ensure a secure and correct connection.
7. セキュアパネル: Close and secure any service panels that were opened.
8. 初期費用： As per safety instructions, the new battery pack must be fully charged before initial use. Connect the CNC system to power and allow it to charge the battery as per the system's charging protocol.

インストール手順が不明な場合は、資格のある技術者にご相談ください。

5. 操作手順

Once the replacement battery is installed and fully charged, the GE FANUC CNC POWER MATE E system should operate as intended. The battery primarily serves to maintain critical system memory and settings during power outages or when the main power is disconnected.

• 電源オン: Power on your GE FANUC CNC POWER MATE E system as you normally would.
• システムチェック: Verify that all system functions, especially those reliant on battery backup (e.g., memory retention, clock settings), are operating correctly.
• 通常操作: Use your CNC system according to its original operating manual. The replacement battery functions seamlessly with the system's power management.

The battery itself does not require direct user interaction during normal operation. Its function is automatic.

6. メンテナンス

The Technical Precision replacement battery is designed for long-term, maintenance-free operation. However, observing the following general guidelines can help ensure its longevity:

• 温度： Operate the CNC system within its recommended temperature range. Avoid exposing the battery to extreme heat or cold, as this can degrade performance and lifespan.
• 物理検査: Periodically inspect the battery and its connections for any signs of physical damage, corrosion, or loose connections. Ensure the battery label remains intact.
• ストレージ： If the CNC system is to be stored for an extended period, ensure the battery is adequately charged before storage. Store the system in a cool, dry place.
• 交換： Replace the battery when its capacity diminishes or if the CNC system indicates a battery fault. The lifespan of a battery depends on usage patterns and environmental conditions.

7。 トラブルシューティング

If you encounter issues after replacing the battery, consider the following:

For complex issues, contact Technical Precision customer support or a qualified CNC technician.

8. 仕様

9. 保証とサポート

For warranty information or technical support regarding your Technical Precision replacement battery, please contact the manufacturer directly.

メーカー: 技術的精度

Refer to the product packaging or the Technical Precision official web最新の連絡先情報と保証の詳細については、サイトをご覧ください。

Note: Warranty may be void if the battery label is removed or if the product is misused.