Akozon Pressure Sensor User Manual

1.製品オーバーview

The Akozon pressure sensor is a high-quality, stainless steel transducer designed for accurate pressure measurement across various media. It features a standard 1/8 inch NPT thread, making it suitable for a wide range of applications including oil, fuel, gas, water, and air pressure systems. This sensor provides a reliable and precise output for monitoring system pressures.

Figure 1: Akozon 1/8 inch NPT Pressure Sensor. This image shows the overall design of the pressure sensor, highlighting its stainless steel body and electrical connector.

2. 主な特徴

• 高精度: Provides a small output error of ±2% FS, including non-linearity, hysteresis, and repeatability across the full temperature range.
• 耐久性のある構造: Manufactured from high-quality stainless steel, ensuring rust-free performance, corrosion resistance, and maximum durability.
• 幅広い応用範囲: Suitable for measuring pressure in oil, fuel, gas, water, and air systems, compatible with various tanks and lines.
• 簡単なインストール: Features a 1/8 inch NPT thread for simple and direct replacement or installation without the need for complex tools.

3. 仕様

4. セットアップとインストール

This pressure sensor is designed for straightforward installation. Follow these steps for proper setup:

1. 準備： Ensure the system where the sensor will be installed is depressurized and cooled, if applicable.
2. Thread Application: Apply appropriate thread sealant (e.g., PTFE tape or liquid sealant) to the 1/8 inch NPT threads of the sensor to ensure a leak-proof connection.
3. 取り付け: Carefully thread the sensor into the designated port. Tighten it securely, but avoid over-tightening, which can damage the threads or the sensor.
4. 電気接続: Connect the sensor's electrical connector to your monitoring or control system. Refer to your system's wiring diagram for correct pin assignments. Ensure connections are secure and insulated.
5. 検証： After installation, slowly repressurize the system and check for any leaks around the sensor's threads. Verify that the sensor is providing readings to your monitoring system.

Figure 2: Close-up of the sensor's 1/8 inch NPT thread and electrical connector. This image details the connection points for installation.

5. 操作手順

Once installed and connected, the Akozon pressure sensor operates by converting the applied pressure into a proportional electrical signal. This signal can then be read by a compatible gauge, display, or control unit.

• 電源オン: Ensure your monitoring system is powered on and correctly configured to receive input from the sensor.
• 圧力モニタリング： The sensor will continuously transmit pressure data. Monitor the readings on your connected device.
• 動作範囲: Ensure the pressure being measured remains within the sensor's specified operating range (e.g., 300 PSI). Operating outside this range may lead to inaccurate readings or sensor damage.
• 温度に関する考慮事項: The sensor is designed to operate within a specific temperature range (up to 120°C). Extreme temperatures can affect accuracy and lifespan.

6. メンテナンス

To ensure optimal performance and longevity of your Akozon pressure sensor, follow these maintenance guidelines:

• 定期点検: センサーとその接続部に物理的な損傷、腐食、配線の緩みなどの兆候がないか定期的に点検してください。
• クリーニング： Keep the exterior of the sensor and its electrical connector clean. Use a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
• 接続の整合性: Ensure all electrical connections remain tight and free from moisture or contaminants.
• 環境保護: Protect the sensor from direct exposure to extreme weather conditions, excessive vibration, or impacts that could compromise its integrity.

7。 トラブルシューティング

If you encounter issues with your Akozon pressure sensor, consider the following troubleshooting steps:

• 読み取れない、または読み間違える:
  • すべての電気接続が適切に固定され、導通しているかどうかを確認します。
  • Verify that the sensor is receiving the correct supply voltag（5V DC）。
  • Ensure the pressure being measured is within the sensor's specified operating range.
  • Inspect the sensor for any visible damage or blockages in the pressure port.
• 接続部の漏れ:
  • システムを減圧します。
  • Remove the sensor, reapply thread sealant, and reinstall, ensuring proper tightening.
• 断続的な測定値:
  • Check for loose wiring or intermittent electrical contact.
  • Ensure the sensor is not subjected to excessive vibration.

これらの手順を実行しても問題が解決しない場合は、カスタマー サポートに問い合わせて、さらにサポートを受けてください。

8. 保証とサポート

Akozon is committed to providing high-quality products and customer satisfaction. If you have any questions, concerns, or require technical assistance with your pressure sensor, please do not hesitate to contact our customer service team.

Our support team is available to help you with installation, operation, troubleshooting, and any other product-related inquiries. Please have your model number (792117337086) ready when contacting support to ensure efficient service.

For contact information, please refer to the Akozon official webサイトまたは購入書類をご覧ください。