1. はじめに
This manual provides essential information for the proper installation, operation, and maintenance of your Cloudray F-Theta Fiber Laser Lens. This lens is designed for 1064nm fiber laser machines, offering a 150x150mm scanning field and a focal length of 225mm. F-Theta lenses are critical components in laser marking, engraving, and drilling applications, enabling precise and fast laser beam positioning and focusing across a defined work area.
The lens features high stability, wear resistance, and high-temperature resistance, contributing to better thermal stability and reduced thermal focus shift. Its anti-reflective coatings ensure high transmittance (up to 97%) and a long service life.
Figure 1: Cloudray F-Theta Fiber Laser Lens installed on a fiber laser marking machine. The lens is highlighted, showing its position relative to the laser head.
2. セットアップとインストール
The Cloudray F-Theta lens is designed for straightforward installation. It features a standard M85x1 threading, allowing for easy replacement or upgrade in most compatible laser marking machines.
- 開梱: Carefully remove the lens from its packaging. Inspect for any visible damage.
- 準備： Ensure the laser machine is powered off and disconnected from the power source before handling any components. Wear appropriate protective gloves to prevent fingerprints or contaminants on the optical surfaces.
- 取り付け: Align the M85x1 thread of the F-Theta lens with the corresponding mounting on your laser machine's galvo head. Gently screw the lens into place. Do not overtighten, as this can cause damage to the threads or the lens housing.
- 焦点距離調整: After installation, it is crucial to adjust the focal length within your laser software to match the new lens. Refer to your laser machine's software manual for specific instructions on calibrating the focal length and scan field.
図 2: 拡大図 view demonstrating the M85x1 threading for easy installation of the F-Theta lens into a fiber laser marking machine's galvo head.
Video 1: This video demonstrates the physical installation of the Cloudray F-Theta lens onto a laser marking machine and the initial setup steps.
3. 操作手順
The F-Theta lens works in conjunction with galvo mirrors to direct and focus the laser beam across the marking area. Proper calibration within your laser software is essential for accurate and consistent results.
- ソフトウェア構成： Open your laser marking software (e.g., Ezcad2). Navigate to the configuration parameters for the field settings.
- Field Size Input: Enter the correct field size for your 150x150mm lens (e.g., 150mm for both X and Y axes).
- 校正プロセス： Use the software's calibration function to fine-tune the laser's scanning accuracy. This typically involves marking a known pattern (e.g., a square) and measuring its dimensions to adjust the galvo scale factors. Repeat this process until the marked dimensions precisely match the intended design.
- フォーカス: Ensure the workpiece is at the correct focal distance from the lens. Many machines use a red light pointer for approximate focusing, which should be adjusted until the red dots converge into a single, sharp point on the material surface.
Figure 3: A diagram illustrating the optical path of a laser beam through galvano scanners and an F-Theta lens, showing how the beam is directed and focused onto the scanning area.
Video 2: This video demonstrates the software calibration process for the F-Theta lens, including setting field parameters and adjusting scale factors for accurate marking.
4. メンテナンス
Proper maintenance ensures the longevity and optimal performance of your F-Theta lens.
- クリーニング： Only clean the lens surfaces when necessary, using specialized optical lens cleaning solutions and lint-free optical wipes. Avoid touching the lens surface with bare hands.
- 防塵： Always keep the protective caps on the lens when it is not in use or when removed from the machine to prevent dust accumulation.
- ストレージ： Store the lens in a clean, dry, and temperature-controlled environment, away from direct sunlight and corrosive chemicals.
- 検査： Periodically inspect the lens for any signs of damage, scratches, or contamination.
Figure 4: The Cloudray F-Theta lens shown with its protective caps, emphasizing the importance of covering the optics when not in use.
5。 トラブルシューティング
If you encounter issues with your laser marking results, consider the following common troubleshooting steps:
- Poor Focus/Blurry Marks: Verify that the focal distance is correctly set for your material and that the lens is securely mounted. Re-calibrate the software's field settings if necessary.
- Inconsistent Marking Area: Re-check the software's field calibration. Ensure the galvo mirrors are clean and functioning correctly.
- Reduced Laser Power/Weak Marks: Inspect the lens for any contamination or damage that might be obstructing the laser path. Ensure the laser source is operating at optimal parameters.
- 物理的ダメージ: If the lens appears physically damaged, it may need replacement.
For persistent issues, contact Cloudray technical support for assistance.
6. 仕様
Key specifications for the Cloudray F-Theta Fiber Laser Lens (150x150mm FL225mm M85):
| 仕様 | 価値 |
|---|---|
| メーカー | クラウドレイ |
| 部品番号 | FSL02H150F225 |
| アイテム重量 | 15.5オンス |
| 製品寸法 | 5.91 x 5.91 x 5.91インチ |
| 商品型番 | デフォルトM85 |
| サイズ | 150x150mm FL225mm |
| 色 | 1064nm |
| 材料 | F-Theta lens |
| 焦点距離の説明 | 225mm（8.8インチ） |
| レンズタイプ | 標準 |
| 互換性のある取り付け | 1064nm |
| カメラレンズの説明 | Scan Field 150x150mm FL 225mm |
Figure 5: A detailed table outlining the specifications for various Cloudray F-Theta lenses, including focal length, back working distance, scan length, and mounting thread.
7. 保証とサポート
Cloudray products are backed by a 2-year comprehensive coverage. Additionally, lifetime technical support is provided to guide you through every stage, from pre-purchase planning to post-purchase optimization. For any inquiries or support needs, please contact Cloudray customer service.
