Fuers TL-2600 Fake Camera Instruction Manual

1.製品オーバーview

The Fuers TL-2600 is a high-quality, durable dummy surveillance camera designed to deter potential intruders. It features a realistic appearance, a flashing LED light, and is suitable for both indoor and outdoor use. This device provides a cost-effective solution to enhance security visibility without the complexity of a real surveillance system.

主な特徴:

• リアルなデザイン: High resemblance to actual security cameras.
• LED ライトの点滅: Simulates active surveillance, powered by 2 AAA batteries (not included).
• 耐久性のある構造: Made from high-quality ABS material, weather-resistant for outdoor use.
• 調整可能な角度: Features a mounting bracket allowing for 90° vertical and 360° horizontal rotation.
• 簡単なインストール: No wiring required, mounts quickly to walls or ceilings.

Image 1.1: The Fuers TL-2600 Fake Camera featuring a red flashing LED light, simulating active operation.

Image 1.2: The camera's adjustable bracket allows for 90-degree vertical and 360-degree horizontal rotation for optimal positioning.

2. パッケージ内容

以下にリストされているすべてのアイテムがパッケージに含まれていることを確認してください。

• 1 x Fuers TL-2600 Dummy Camera Unit
• 取り付けブラケット x 1 (取り付け済み)
• 取り付けネジ3本
• 3x壁プラグ
• 1 x CCTV Warning Sticker

注記： 2 x AAA batteries are 含まれません 別途購入する必要があります。

Image 2.1: Contents of the package including the dummy camera, mounting hardware, and a CCTV sticker. Dimensions are also shown.

3. セットアップ

3.1 バッテリーの取り付け

1. Locate the battery compartment on the underside of the camera body.
2. コンパートメントカバーを慎重に開けます。
3. 正しい極性 (+/-) に注意しながら、単 4 電池 2 本 (別売) をコンパートメントに挿入します。
4. Close the battery compartment cover securely. The LED light should begin flashing immediately.

画像3.1: View of the battery compartment opened to insert two AAA batteries.

Image 3.2: Step-by-step guide for installing batteries into the dummy camera.

3.2カメラの取り付け

1. Choose a suitable location for installation, such as a wall or ceiling, ensuring good visibility and deterrence.
2. Position the mounting bracket at the desired location and mark the three screw holes.
3. Drill pilot holes at the marked spots. For masonry or drywall, insert the provided wall plugs.
4. 付属のネジを使用して取り付けブラケットを表面に固定します。
5. Adjust the camera angle as needed (refer to Section 4.1).
6. Affix the included CCTV warning sticker in a prominent location nearby to further enhance deterrence.

4. 操作手順

4.1 カメラアングルの調整

The camera's mounting bracket allows for flexible positioning:

• 垂直方向の調整: Loosen the side screw on the bracket to tilt the camera up or down (up to 90°). Tighten the screw once the desired angle is achieved.
• 水平調整: The base of the bracket allows for full 360° rotation. Simply rotate the camera body to face the desired direction.

4.2 LED点滅

Once batteries are correctly installed, the red LED light will automatically begin to flash continuously. There is no separate on/off switch for the LED. The flashing LED simulates the operation of a real security camera, enhancing its deterrent effect.

5. メンテナンス

• バッテリー交換: Replace the two AAA batteries when the LED light stops flashing or becomes dim. Always use fresh batteries for optimal performance.
• クリーニング： Wipe the camera body and lens area with a soft, damp 布でほこりや汚れを拭き取ってください。刺激の強い化学薬品や研磨剤入りの洗剤の使用は避けてください。
• 耐候性: While designed for outdoor use, extreme weather conditions (e.g., heavy storms, prolonged direct sunlight) may affect its lifespan. Periodically check the unit for any signs of wear or damage.

6。 トラブルシューティング

• LEDが点滅しない:
  • 電池が正しい極性で正しく取り付けられているかどうかを確認してください。
  • 新しい単XNUMX電池と交換してください。
• Camera Feels Loose After Mounting:
  • すべての取り付けネジがしっかりと締められていることを確認してください。
  • If mounted on drywall, ensure wall plugs are properly seated.

7. 仕様