RISCO RK815DTG300B Dual Technology Detector

1. はじめに

This manual provides detailed instructions for the installation, operation, and maintenance of the RISCO RK815DTG300B Dual Technology Detector. This device combines Passive Infrared (PIR) and Microwave (MW) detection technologies to offer reliable and accurate motion sensing for security applications. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

2 製品の特徴

The RISCO RK815DTG300B detector is designed with advanced features to enhance security and minimize false alarms:

• Dual Technology Detection: Combines dual-element PIR and 10.25 GHz Microwave for superior detection and false alarm immunity.
• Anti-Cloak Technology (ACT) Green Line: Deactivates the microwave channel when the system is disarmed, reducing power consumption and extending product life.
• Active Infrared Anti-Masking: Detects attempts to block the detector's field of view, providing enhanced tamp保護。
• Selectable End-of-Line (EOL) Resistors: Configurable via jumpers for flexible wiring with various control panels.
• Tamper保護： Features anti-opening and anti-dismount (wall/angle) tamper switches to alert against unauthorized access or removal.
• Adjustable Microwave Sensitivity: Allows fine-tuning of the microwave detection range.
• Advanced Detection Zones: Provides 30 detection zones across 4 levels with anti-radiation features.
• 視覚的なインジケーター: Equipped with 3 LED indicators for status and detection events.
• True Temperature Compensation: Ensures consistent detection performance across varying ambient temperatures.
• High Immunity: Excellent immunity to Radio Frequency (RF) interference and white light, reducing false alarms.

3. 安全情報

次の安全上の注意事項を守ってください。

• Installation should be performed by qualified personnel only, in accordance with local electrical codes and regulations.
• 配線やメンテナンスを行う前に電源を切ってください。
• デバイスを湿気、極端な温度、直射日光にさらさないでください。
• 取り付け面が安定していて安全であることを確認してください。
• デバイスを強い電磁場から遠ざけてください。

4. パッケージ内容

パッケージにすべてのアイテムが揃っていることを確認します。

• RISCO RK815DTG300B Dual Technology Detector unit
• 取り付けネジとアンカー
• インストールガイド/ユーザーマニュアル（この文書）
• Optional lenses (if purchased separately)

5. セットアップとインストール

最適なパフォーマンスを得るには、適切なインストールが不可欠です。以下の手順を慎重に実行してください。

5.1取り付け位置

Choose a mounting location that provides the best coverage of the protected area. Avoid placing the detector directly facing heat sources, windows, or areas with strong air currents. The ideal mounting height is typically 2.1 to 2.7 meters (7 to 9 feet) above the floor.

5.2 検出器を開く

Carefully open the detector casing by releasing the locking tab, usually located at the bottom or side of the unit. This will expose the terminal block and jumper settings.

5.3配線

Connect the detector to the control panel according to the panel's instructions and the detector's terminal markings. Ensure correct polarity for power connections. Utilize the selectable EOL resistors via jumpers as required by your security system.

端末接続:

• + / - : Power input (typically 9-16 VDC).
• 警報： Normally Closed (NC) alarm output.
• TAMPER: ノーマルクローズ（NC）tamper出力。
• マスク： Anti-masking output (if used).

5.4ジャンパー設定

Configure the jumpers for EOL resistors, microwave sensitivity, and ACT Green Line functionality as needed for your specific installation.

5.5 検出器の取り付け

Secure the detector base to the wall or corner using the provided screws and anchors. Ensure the tamper switch is properly engaged with the mounting surface.

Figure 1: RISCO RK815DTG300B Dual Technology Detector. This image shows the front view of the detector, typically mounted on a wall or in a corner, indicating its compact design and sensor window.

5.6歩行テスト

After installation, perform a walk test to verify the detection coverage. Walk through the protected area and observe the LED indicators to confirm proper detection. Adjust the microwave sensitivity if necessary.

6. 操作手順

The RK815DTG300B detector operates automatically once powered and configured. It continuously monitors the protected area using both PIR and Microwave technologies.

6.1 Detection Logic

For an alarm to be triggered, both the PIR and Microwave sensors must detect motion simultaneously (AND logic), significantly reducing false alarms compared to single-technology detectors.

6.2 LEDインジケーター

The detector features three LEDs to indicate its status:

• PIR LED: Illuminates when the PIR sensor detects motion.
• MW LED: Illuminates when the Microwave sensor detects motion.
• アラーム LED: Illuminates when both PIR and MW detect motion, triggering an alarm.

6.3 Anti-Cloak Technology (ACT) Green Line

When enabled, the ACT Green Line feature automatically deactivates the microwave sensor when the security system is disarmed. This conserves energy and extends the lifespan of the microwave component. The microwave sensor reactivates automatically when the system is armed.

7. メンテナンス

The RISCO RK815DTG300B detector requires minimal maintenance to ensure continued reliable operation.

• クリーニング： Periodically clean the detector's lens and casin柔らかく乾いた布で拭いてください。研磨剤入りの洗剤や溶剤は使用しないでください。
• 検査： Annually inspect the detector for any signs of damage, loose wiring, or obstructions to its field of view.
• 歩行テスト： Perform a walk test periodically (e.g., every 6-12 months) to confirm the detector is functioning correctly.

8。 トラブルシューティング

If you experience issues with your detector, refer to the following common problems and solutions:

If the problem persists, contact your security system installer or RISCO technical support.

9. 仕様

10. 保証とサポート

For warranty information, please refer to the documentation provided with your purchase or visit the official RISCO Group website. For technical support, contact your authorized RISCO installer or the RISCO customer service department.

RISCOグループ Webサイト： www.riscogroup.com