BTF-LIGHTING 16.4ft Warm White SMD5630 LED Strip Light User Manual

導入

This manual provides essential information for the safe and effective installation, operation, and maintenance of your BTF-LIGHTING 16.4ft Warm White SMD5630 LED Strip Light. Please read this manual thoroughly before use and retain it for future reference.

安全情報

設置またはメンテナンスの前に、電源が切断されていることを確認してください。
This LED strip is designed for 12V DC power only. Connecting to a higher voltageは製品を損傷します。
This product is IP30 rated, meaning it is non-waterproof. Avoid exposure to water or high humidity.
Do not bend the LED strip sharply or apply excessive force, as this may damage the circuit board or LEDs.
過熱を防ぐために、LED ストリップの周囲に適切な換気を確保してください。
お子様の手の届かない場所に保管してください。
Only use the recommended power adapter (DC12V3A) or a compatible power supply.

パッケージ内容

すべてのコンポーネントが存在し、良好な状態であることを確認します。

1 x BTF-LIGHTING 16.4ft (5m) Warm White SMD5630 LED Strip Light
1 x Remote Control (if included with your specific package)
Note: Power adapter is typically sold separately.

仕様

ブランド	BTF-照明
モデル番号	56305MWW60W30
LEDタイプ	SMD5630
LED数量	300個のLED（60個のLED/メートル）
ストリップ長さ	16.4フィート（5メートル）
FPCB Board Width	10mm
ライトカラー	ウォームホワイト
色温度	2700K-3000K
LEDあたりのルーメン	23-25 lm/LED
ワーキングVoltage	DC12V
推奨電源アダプター	DC 12V 3A (36W) or higher
ワットtage	30ワット
防水レベル	IP30 (Non-Waterproof)
動作温度	-20°C ～ 50°C
寿命	>50,000時間
認定資格	CEおよびRoHS

セットアップ手順

表面を準備する: Ensure the installation surface is clean, dry, and smooth. Dust, oil, or moisture can reduce the adhesive's effectiveness.
画像: クローズアップ view of the LED strip, highlighting individual SMD5630 LEDs and designated cut points marked with a scissor icon. The strip also shows the adhesive backing being peeled.
測定とカット（オプション）: If a shorter length is required, cut the LED strip only at the designated cut marks (usually indicated by a scissor icon and copper pads). Cutting elsewhere will damage the circuit and prevent the section from lighting up.
接続電源：
- Identify the 2-pin connectors on the LED strip.
- Connect the LED strip's 2-pin connector to a compatible DC 12V power adapter (not included). Ensure polarity is correct (positive to positive, negative to negative).
- If a remote control is included, connect the LED strip to the remote controller, and then connect the controller to the power adapter.
Image: Two separate sections of the LED strip, each terminating with a 2-pin connector (red and black wires), ready for connection to a power source or controller.
Test Before Adhering: Before removing the adhesive backing, plug in the power adapter to test if the LED strip lights up correctly. This allows for troubleshooting before permanent installation.
ストリップを貼り付けます: Once tested, peel off the protective backing from the adhesive tape on the back of the LED strip. Carefully press the strip onto the desired clean, dry surface. Apply firm, even pressure along the entire length to ensure good adhesion.

操作手順

Once the LED strip is properly installed and connected to a 12V DC power supply:

電源オン/オフ: Plug the power adapter into a wall outlet to turn the strip light on. Unplug it to turn it off.
Using the Remote Control (if applicable): If your package included a remote control, refer to its specific instructions for functions such as brightness adjustment or on/off control.

Examples of warm white LED strip lighting in various indoor settings

画像: Visual examples of LED strip lighting used in different indoor environments, demonstrating the warm white illumination. This image also shows Cool White and Nature White, but this product is Warm White.

メンテナンス

クリーニング： Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
検査： Periodically check the strip for any signs of damage, loose connections, or adhesive degradation.
ストレージ： If storing the LED strip, ensure it is kept in a dry, cool place, away from direct sunlight and extreme temperatures.

トラブルシューティング

問題	考えられる原因	解決
LEDストリップが点灯しません。	アダプタに電力が供給されていません。電源接続が正しくありません（極性が逆です）。電源アダプタの不良。破損した LED ストリップ。 Remote control battery dead or not paired (if applicable).	壁のコンセントと電源アダプタの接続を確認してください。 Ensure positive (+) and negative (-) connections are correct. Test with a known working 12V DC power adapter. 特に切断箇所に目に見える損傷がないかストリップを検査します。 Replace remote battery or re-pair according to remote instructions.
LED ストリップの一部が点灯しません。	ストリップの一部に損傷があります。 Incorrect cutting.	Inspect the unlit section for physical damage or a broken circuit. Ensure cuts were made only at designated marks. Damaged sections cannot be repaired.
LED が暗かったり、ちらついたりしています。	電力供給が不十分です。接続が緩んでいます。	電源アダプターが十分な電力を供給していることを確認してくださいtage (minimum 30W for this strip). すべての接続が確実に固定されているかどうかを確認します。

保証とサポート

BTF-LIGHTING products are designed for reliability and performance. For warranty information, technical support, or assistance with your product, please contact BTF-LIGHTING customer service through the retailer where the product was purchased or visit the official BTF-LIGHTING webサイト。

Please have your model number (56305MWW60W30) and purchase details ready when contacting support.

BTF-LIGHTING 56305MWW60W30