M-Wave M30HCW Bicycle Computer

1. はじめに

Thank you for choosing the M-Wave M30HCW Wireless Bicycle Computer. This device is designed to enhance your cycling experience by providing comprehensive data about your rides. It features wireless transmission for a clean setup and a wide range of functions to track your performance and progress. Please read this manual carefully before installation and use to ensure optimal performance and longevity of your device.

Image 1.1: M-Wave M30HCW Bicycle Computer. This image displays the main unit of the M-Wave M30HCW bicycle computer, showcasinコンパクトなデザインとクリアなディスプレイが特徴です。

2. 安全情報

• Always prioritize road safety. Do not operate the computer or adjust settings while cycling in traffic.
• Ensure the computer is securely mounted to prevent it from detaching during your ride.
• 電池はお子様の手の届かないところに保管してください。 飲み込んだ場合は、直ちに医師の診察を受けてください。
• 電池は地域の規制に従って廃棄してください。焼却しないでください。
• The device has an Ingress Protection rating of IP44, meaning it is protected against splashing water from any direction. It is not designed for submersion.

3. パッケージ内容

パッケージにすべてのアイテムが揃っていることを確認します。

• M-Wave M30HCW Cyclocomputer Unit
• Wireless Speed/Cadence Sensor
• ホイールマグネット
• Mounting Bracket (for handlebar or stem)
• Mounting Ties/Bands
• CR2 Batteries (4 required, included)

4. セットアップ

4.1. バッテリーの取り付け

1. Open the battery compartment on the back of the cyclocomputer unit and the wireless sensor.
2. 正しい極性 (+/-) を確認して CR2 電池を挿入します。
3. 電池ケースをしっかりと閉めてください。

4.2. Mounting the Cyclocomputer

The M-Wave M30HCW features tool-free mounting for quick installation.

1. Attach the mounting bracket to your bicycle's handlebar or stem using the provided ties or bands. Ensure it is firmly secured and positioned for easy viewing。
2. Slide the cyclocomputer unit onto the mounting bracket until it clicks into place.

4.3. Mounting the Wireless Sensor and Magnet

1. Attach the wireless sensor to the front fork of your bicycle, ensuring it is aligned with the wheel spokes.
2. Mount the wheel magnet to a spoke on the front wheel. Position the magnet so it passes within 5mm of the sensor as the wheel rotates.
3. Ensure the sensor and magnet are securely fastened and do not interfere with wheel rotation or braking.

4.4. 初期設定

After battery installation, the computer will typically prompt you for initial settings. Use the buttons (usually MODE and SET) to navigate and confirm selections.

• 単位: Select between metric (km/h, km) and imperial (mph, miles) units.
• ホイールサイズ: Input your wheel circumference in millimeters (mm). Refer to your bicycle tire for this value or measure it accurately. This is crucial for accurate speed and distance readings.
• 時間： 現在の時刻を設定します (24 時間形式または 12 時間形式)。
• 重さ： Enter your body weight for calorie calculation.

5. 操作手順

The M-Wave M30HCW features an LED backlit display for easy reading and is operated via buttons, typically located on the front or bottom of the unit.

5.1.基本機能

The computer automatically powers on and off. When you start cycling, it will activate and begin recording data. When stationary, it will enter a power-saving mode.

• 現在の速度: Displays your real-time cycling speed.
• 平均速度： Shows the average speed for your current ride.
• 最高速度: Records the highest speed achieved during your ride.
• 旅行距離: 現在の走行でカバーされた距離を測定します。
• オドメーター： Tracks the total accumulated distance.
• 乗車時間: Records the duration of your current ride.
• ケイデンス： 1 分間のペダリング回転数 (RPM) を測定します。
• 高度計： Provides altitude measurements for climb tracking.
• Heart Rate Monitor/Alarm: (If applicable, requires compatible HR sensor, not included with base unit) Monitors heart rate and can alert if thresholds are exceeded.
• カロリー消費量: Estimates calories burned based on ride data and user weight.
• 温度計: 周囲温度を表示します。

5.2. ボタン操作

Typically, the computer will have one or two buttons for navigation and selection:

• モードボタン: Press briefly to cycle through different display modes (e.g., speed, distance, time). Press and hold to enter settings or reset trip data.
• SETボタン： Used to confirm selections or adjust values within settings menus.

Refer to the on-screen prompts for specific button functions during setup and operation.

6. メンテナンス

• クリーニング： コンピューターユニットとセンサーを柔らかくて乾いた布で拭いてください。amp 布で拭いてください。研磨剤や溶剤は使用しないでください。
• 耐水性: The device is IP44 rated, protecting it from splashing water. Avoid high-pressure washing or submerging the unit.
• バッテリー交換: Replace batteries when the low battery indicator appears on the display. Ensure proper battery type and polarity.
• ストレージ： If storing the bicycle for an extended period, remove the batteries from the computer and sensor to prevent leakage.

7。 トラブルシューティング

8. 仕様

9. 保証とサポート

For warranty information and technical support, please refer to the documentation provided with your purchase or contact M-Wave customer service directly. Keep your proof of purchase for any warranty claims.