1. はじめに
The Altronix Tempo2 Digital Timer is a versatile two-stage timer designed for various applications requiring precise timing control. It operates on either 12 or 24 volt AC or DC power and features a Single Pole Double Throw (SPDT) contact rated for 2 amps at 115VAC or 28VDC. Key functionalities include an adjustable timing range from 1 second to 60 seconds for timed door release, daily/weekly test modes, one-shot activation, and a door prop alarm. The unit incorporates EEProm memory for settings retention and an LCD display for clear status indication.
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Tempo2 Digital Timer to ensure optimal performance and longevity.
Image showing the Altronix Tempo2 Digital Timer unit, typically featuring its LCD display and control buttons.
2. 特徴
- ユニバーサルツーStage タイマー: Provides flexible timing control for various applications.
- 柔軟な電源入力: Operates on 12V or 24V AC or DC.
- SPDT Contact: 2 と評価 Amp / 115VAC / 28VDC.
- Adjustable Timing Range: 1 second to 60 seconds for timed door release.
- 動作モード： Includes daily/weekly test mode and one-shot activation.
- Door Prop Alarm: Integrated alarm function for security applications.
- EEProm Memory: Retains programmed settings during power loss.
- LCDディスプレイ: Provides clear visual feedback for programming and status.
3. セットアップとインストール
Proper installation is crucial for the reliable operation of the Tempo2 Digital Timer. Ensure all power is disconnected before beginning installation.
3.1 取り付け
Mount the timer in a secure, dry location, away from direct heat sources or excessive moisture. Use appropriate fasteners for the mounting surface.
3.2配線接続
Refer to the wiring diagram provided with your unit for specific connection points. General wiring guidelines are as follows:
- 電源入力: Connect 12V or 24V AC/DC power to the designated terminals. Observe correct polarity for DC connections.
- トリガー入力： Connect the trigger source (e.g., door contact, push button) to the trigger input terminals.
- リレー出力： Connect the device to be controlled (e.g., door strike, alarm panel) to the SPDT relay output terminals (Common, Normally Open, Normally Closed). Ensure the load does not exceed the 2 Amp / 115VAC / 28VDC rating.
注意： Incorrect wiring can damage the unit or connected equipment. If you are unsure about any wiring procedures, consult a qualified electrician or technician.
4. 操作手順
The Tempo2 Digital Timer features an LCD display and control buttons for programming and operation.
4.1 Setting the Timer Duration
- Access the programming menu using the designated button (refer to the unit's specific button layout).
- Navigate to the 'Timing Duration' setting.
- Adjust the time from 1 second to 60 seconds using the up/down buttons.
- Save the setting and exit the programming menu.
4.2 Daily/Weekly Test Mode
This mode allows for scheduled testing of the timer's functionality without full activation. Consult the unit's programming guide for setting specific test schedules.
4.3 One-Shot Activation
The one-shot activation feature allows the timer to trigger once for the set duration upon receiving a signal. This is useful for single-event operations.
4.4 ドア プロップ アラーム
When configured, the door prop alarm will activate if a connected door remains open beyond a pre-set time. This feature enhances security by alerting users to prolonged open door conditions.
5. メンテナンス
The Altronix Tempo2 Digital Timer is designed for reliable, long-term operation with minimal maintenance. Follow these guidelines to ensure continued performance:
- クリーニング： Periodically wipe the unit with a soft, dry cloth to remove dust and debris. Do not use abrasive cleaners or solvents.
- 接続: すべての配線接続が安全で腐食がないことを確認するために毎年点検してください。
- 環境： 動作環境が指定された温度と湿度の範囲内であることを確認してください。
ユニット内部にはユーザーが修理可能な部品はありません。修理はすべて資格を持った担当者にご依頼ください。
6。 トラブルシューティング
If you encounter issues with your Tempo2 Digital Timer, refer to the following common problems and solutions:
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Timer not powering on / LCD blank | 電源が入らない、音量が正しくないtage, or reversed DC polarity. | 電源の接続とボリュームを確認してくださいtage. Ensure correct DC polarity. |
| Timer not activating output | Incorrect trigger input, faulty wiring, or incorrect programming. | Verify trigger input signal. Check output wiring. Review プログラミング設定。 |
| タイミング期間が正しくありません | Timer duration set incorrectly. | Re-enter the programming menu and adjust the timing duration as needed. |
| Door prop alarm not functioning | Door contact faulty, wiring issue, or alarm not enabled. | Check door contact and its wiring. Ensure door prop alarm is enabled in settings. |
If the problem persists after attempting these solutions, contact Altronix technical support for further assistance.
7. 仕様
- モデル： TEMPO2
- ブランド： アルトロニクス
- 電源入力: 12Vまたは24V AC/DC
- 連絡先の種類: SPDT（単極双投）
- 連絡先の評価: 2 Amp @ 115VAC / 28VDC
- タイミング範囲: 1 second to 60 seconds (adjustable)
- メモリ： EEProm (retains settings)
- 画面： 液晶
- 特徴： 2つのtage operation, daily/weekly test mode, one-shot activation, door prop alarm
- 商品の重量: 約0.2ポンド（0.09 kg）
- 国際コード: 782239938292
- GTIN: 782239938292
8. 保証とサポート
Altronix products are backed by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty information included with your product packaging or visit the official Altronix webサイト。
For technical support, troubleshooting assistance, or to inquire about service, please contact Altronix customer support. Have your model number (TEMPO2) and any relevant purchase information ready when contacting support.
Altronix Contact Information:
Please refer to the official Altronix webテクニカル サポートの電話番号や電子メール アドレスなどの最新の連絡先情報については、こちらのサイトをご覧ください。