NVX NSW102v3

NVX NSW102v3 10-inch Dual 2-Ohm Car Subwoofer Instruction Manual

Model: NSW102v3 | Brand: NVX

導入

The NVX NSW102v3 is a high-performance 10-inch car subwoofer designed to deliver powerful and accurate bass. This N-Series subwoofer features robust construction and advanced components for an immersive audio experience in your vehicle. This manual provides essential information for the proper installation, operation, and maintenance of your subwoofer.

フロント view of the NVX NSW102v3 10-inch subwoofer

画像: フロント view of the NVX NSW102v3 10-inch subwoofer, showcasinコーンとサラウンド。

主な特徴:

  • パワフルな低音パフォーマンス: Delivers up to 1000W peak and 500W RMS power for deep, resonant bass.
  • Accurate Sound Reproduction: Equipped with an enhanced pressed paper cone, high-roll foam surround, and a 2.0" high-temperature copper voice coil for minimal distortion and maximum clarity.
  • Durable & Efficient Design: Features a stamped steel vented basket with NVX logo, 112 oz. double-stacked ferrite magnet, and protective rubber boot for reliable, long-lasting performance.
  • 広い周波数応答: Offers a frequency range of 20-200 Hz, a resonance frequency (Fs) of 38.67 Hz, and a sensitivity of 85 dB for dynamic bass.
  • 柔軟なインストールオプション: Compatible with sealed enclosures (0.60 cubic feet) and ported enclosures (1.5 cubic feet).

安全情報

Always observe the following safety precautions during installation and operation to prevent injury or damage to the equipment:

  • Disconnect the vehicle's battery negative terminal before beginning any electrical work.
  • 挟まれたり損傷したりしないように、すべての配線が正しく配線され、固定されていることを確認してください。
  • 電源、アース、スピーカーの接続には適切なゲージの配線を使用してください。
  • 車両の運転や安全装置の妨げになるような場所にサブウーファーを設置しないでください。
  • 高い音圧レベルに長時間さらされると、永久的な聴覚障害を引き起こす可能性があります。音量を調整する際はご注意ください。
  • 取り付け手順が不明な場合は、プロのカーオーディオ設置業者にご相談ください。

セットアップとインストール

エンクロージャの推奨事項:

The performance of your subwoofer is highly dependent on the enclosure it is installed in. The NVX NSW102v3 is designed to perform optimally in the following enclosure types and volumes:

  • 密閉されたエンクロージャ: 0.60 cubic feet (net internal volume)
  • ポート付きエンクロージャ: 1.5 cubic feet (net internal volume, excluding port and subwoofer displacement)

Ensure the enclosure is constructed from sturdy material and is airtight (for sealed) or properly tuned (for ported) to achieve the best sound quality and prevent damage to the subwoofer.

サブウーファーの取り付け:

Carefully place the subwoofer into the mounting hole of your enclosure. Ensure the mounting holes on the subwoofer frame align with the pre-drilled holes on the enclosure. Use appropriate screws to secure the subwoofer firmly. Do not overtighten, as this can strip the mounting holes or damage the frame.

側 view of the NVX NSW102v3 subwoofer showing mounting flange and terminals

画像: 側 view of the NVX NSW102v3 subwoofer, illustrating the mounting flange and terminal connections.

Wiring Configurations (Dual 2-Ohm Voice Coils):

The NSW102v3 features dual 2-Ohm voice coils, offering flexibility in wiring to achieve different impedance loads for your amp常に amp選択したインピーダンスで、ライファイアは安定します。

Close-up of the NVX NSW102v3 subwoofer terminals

画像: Close-up of the NVX NSW102v3 subwoofer's push terminals, showing positive and negative connections for each voice coil.

  • 4オーム負荷(直列配線):

    ボイスコイル1のプラス端子をボイスコイル2のマイナス端子に接続します。次に、 amplifier's positive output to the remaining positive terminal of Voice Coil 2, and the amplifier's negative output to the remaining negative terminal of Voice Coil 1. This configuration results in a 4-Ohm load, suitable for many mono amplifiers。

  • 1オーム負荷(並列配線):

    ボイスコイル1とボイスコイル2のプラス端子を接続します。ボイスコイル1とボイスコイル2のマイナス端子を接続します。次に、 amp溶断器の正出力を結合した正極端子に供給し、 amplifier's negative output to the combined negative terminals. This configuration results in a 1-Ohm load, typically used with high-current, 1-Ohm stable mono amplifiers。

参照してください amp適合インピーダンス負荷については、サブウーファーのマニュアルを参照してください。配線を誤ると、サブウーファーとスピーカーの両方が損傷する可能性があります。 amplifier。

操作手順

Initial Use and Break-in Period:

Allow a break-in period of approximately 10-20 hours of moderate use before operating the subwoofer at high volumes. This allows the suspension components (surround and spider) to loosen up and reach their optimal performance characteristics. During this period, avoid playing the subwoofer at maximum volume or with excessive bass boost.

電力処理:

The NVX NSW102v3 is rated for 500 Watts RMS (Root Mean Square) and 1000 Watts Peak power. RMS power is the continuous power the subwoofer can handle, while peak power is the maximum power it can handle for short bursts. To ensure longevity and optimal performance, it is recommended to match the subwoofer with an amplifier that delivers approximately 500 Watts RMS at the chosen impedance load.

Avoid exceeding the RMS power rating for extended periods, as this can lead to overheating and damage to the voice coil. Ensure your amplifier's gain is set correctly to prevent clipping, which can also damage the subwoofer.

メンテナンス

Proper maintenance will ensure the longevity and performance of your NVX subwoofer.

  • クリーニング: Use a soft, dry cloth to wipe down the subwoofer cone and surround. Avoid using harsh chemicals, solvents, or abrasive cleaners, as these can damage the materials.
  • 検査: Periodically inspect the subwoofer for any signs of damage, such as tears in the cone or surround, loose connections, or unusual odors. Address any issues promptly.
  • 環境: Ensure the subwoofer is installed in a dry environment, protected from direct sunlight and extreme temperatures.

トラブルシューティング

サブウーファーに問題が発生した場合は、次の一般的なトラブルシューティング手順を参照してください。

問題考えられる原因解決
サブウーファーから音が出ない
  • 電力がない ampリファイアー
  • 緩んだ配線または間違った配線
  • Amp保護モードのライフファイア
  • No signal from head unit
  • 電源、アース、リモート電源オンの接続を確認してください。 amplifier。
  • Verify all speaker wires are securely connected and correctly phased.
  • チェック ampヒューズを取り外し、適切なインピーダンス負荷を確保します。
  • Confirm RCA cables are connected and head unit is sending signal.
歪んだ音
  • Ampライファゲインの設定が高すぎる(クリッピング)
  • クロスオーバー設定が正しくありません
  • Damaged subwoofer or enclosure
  • 減らす amp歪みがなくなるまでゲインを上げます。
  • ローパスフィルタ(LPF)を調整する ampリファイアまたはヘッドユニット。
  • Inspect subwoofer cone, surround, and voice coil for damage. Check enclosure for air leaks.
弱い、またはこもった低音
  • Incorrect subwoofer phasing
  • 不十分 ampライフパワー
  • 不適切なエンクロージャボリューム
  • Reverse the polarity of the subwoofer wiring at the amplifier。
  • 確保する amp増幅器の RMS 出力はサブウーファーの RMS 定格と一致します。
  • Verify enclosure volume meets recommended specifications.
サブウーファーの過熱
  • 過剰な電力またはクリッピング
  • 不適切なインピーダンス整合
  • 換気が悪い
  • Reduce volume, check gain settings, and ensure no clipping.
  • 配線構成の一致を確認する ampライファイアの安定したインピーダンス。
  • 確保する ampスピーカーとサブウーファーには十分な空気の流れがあります。

仕様

The following table outlines the key technical specifications for the NVX NSW102v3 10-inch Dual 2-Ohm Car Subwoofer:

特徴仕様
モデル名NS102v3 翻訳
スピーカータイプサブウーファー
スピーカーサイズ10インチ
ウーファー直径10インチ
ボイスコイル構成デュアル2オーム
スピーカー最大出力(ピーク)1000ワット
RMS電力処理500ワット
周波数応答20~200Hz
共振周波数 (Fs)38.67Hz
感度85デシベル
マグネット重量112 oz. (double-stacked ferrite)
コーン素材Enhanced Pressed Paper
サラウンドマテリアルHigh-Roll Foam
ボイスコイル素材High-temperature Copper
バスケットタイプStamped Steel Vented
推奨密閉筐体容積0.60立方フィート
推奨ポート付きエンクロージャ容量1.5立方フィート
アイテム重量14.4 ポンド
製品寸法(奥行き×幅×高さ)奥行き5.7インチ x 幅6.5インチ x 高さ5.7インチ

Note: The listed product dimensions may refer to packaging or a specific component. For precise mounting depth and cutout dimensions, please refer to the product's technical drawing or contact NVX support.

保証情報

The NVX NSW102v3 subwoofer is covered by a Limited Warranty. For detailed information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your purchase or visit the official NVX webサイトでご確認ください。保証請求に備えて購入証明書を保管してください。

サポート

For technical assistance, troubleshooting, or any questions regarding your NVX NSW102v3 subwoofer, please contact NVX customer support. You can typically find contact information on the official NVX webサイトまたは正規販売店を通じてご購入いただけます。

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.