導入
The Flysky FS-GR3E is a reliable 3-channel 2.4GHz receiver designed for use with RC cars and boats. It utilizes Flysky's Automatic Frequency Hopping Digital System (AFHDS) technology to provide a stable and interference-free connection. This receiver is compatible with various Flysky transmitters, including the FS-GT2, FS-GT2B, FS-GT3B, and FS-GT3C. This manual provides essential information for the proper setup, operation, and maintenance of your FS-GR3E receiver.
画像： The Flysky FS-GR3E 3-Channel 2.4GHz Receiver. This image displays the compact black receiver unit with its antenna wire and various ports for connection to servos, ESC, and power.
安全情報
Please read and understand the following safety guidelines before operating your receiver:
- Ensure correct polarity when connecting power to the receiver. Incorrect connections can cause damage.
- RC モデルは、人、車両、障害物から離れた広い場所で操作してください。
- Avoid exposing the receiver to moisture, extreme temperatures, or direct sunlight for extended periods.
- Always turn on your transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.
- すべての配線と接続部に損傷や接触不良がないか定期的に点検してください。
パッケージ内容
パッケージにすべてのアイテムが揃っていることを確認します。
- 1 x Flysky FS-GR3E 2.4GHz 3-Channel Receiver
仕様
| チャンネル | 3 |
| モデルタイプ | 車 / ボート |
| RF受信感度 | -105dbm |
| 変調 | GFSK |
| システムタイプ | AFHDS |
| 感度 | 1024 |
| フェイルセーフ | Yes (Channel 2) |
| バインドポート | Yes (Channel 3) |
| 電源ポート | はい（VCC） |
| 電源入力 | 4-11V DC |
| 重さ | 5g (約0.18オンス) |
| アンテナ長 | 26mm |
| 寸法（長さ×幅×高さ） | 37.6 x 22.3 x 13 mm（約1.48 x 0.88 x 0.51インチ） |
| 色 | 黒 |
設定
1. インストール
Mount the FS-GR3E receiver securely in your RC model, ensuring it is protected from vibrations and moisture. Position the antenna wire as straight as possible and away from metal parts or carbon fiber chassis to maximize range and signal quality. Connect your Electronic Speed Controller (ESC) to Channel 2 (throttle), and your steering servo to Channel 1. If using a third channel for auxiliary functions, connect it to Channel 3.
2. 受信機と送信機のバインド
The receiver must be bound to your Flysky transmitter before use. Follow these steps:
- 送信機の電源がオフになっていることを確認してください。
- Insert the bind plug (usually included with your transmitter or receiver) into the "BIND" port (Channel 3) on the FS-GR3E receiver.
- Connect power to the receiver (e.g., via the ESC or a separate battery pack connected to the VCC port). The receiver's LED should start flashing rapidly, indicating it is in binding mode.
- While holding the bind button on your transmitter (or following its specific binding procedure), power on the transmitter.
- 受信機の LED が点滅を停止して点灯状態になり、バインドが成功したことを示します。
- 受信機をオフにしてから、送信機をオフにします。
- レシーバーからバインドプラグを取り外します。
- Power on the transmitter first, then the receiver. Verify that the receiver's LED is solid and that the controls respond correctly.
Note: If binding fails, repeat the steps. Some transmitters may have slightly different binding procedures; refer to your transmitter's manual for specific instructions.
オペレーティング
1. フェイルセーフ機能
The FS-GR3E receiver features a failsafe function on Channel 2 (throttle) to prevent runaway models in case of signal loss. To set the failsafe position:
- Ensure the receiver is bound to the transmitter and both are powered on.
- Position the throttle stick on your transmitter to the desired failsafe position (e.g., neutral or brake).
- Locate the small failsafe button on the receiver. Press and hold this button until the receiver's LED blinks once, then release.
- The failsafe position is now set. To test, power on the transmitter and receiver, then turn off the transmitter. The throttle should move to the set failsafe position.
It is recommended to set the failsafe to a neutral or brake position for safety.
2. チャネル割り当て
The FS-GR3E receiver has 3 channels. Standard assignments are:
- チャンネル1： Steering (for RC cars/boats)
- チャンネル2： Throttle (for RC cars/boats)
- チャンネル3： Auxiliary function (e.g., lights, gear shift, or used as Bind port)
メンテナンス
To ensure the longevity and optimal performance of your FS-GR3E receiver, follow these maintenance tips:
- Keep the receiver clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air for cleaning.
- Avoid exposing the receiver to water or excessive humidity. If it gets wet, disconnect power immediately and allow it to dry completely before re-use.
- 受信機を使用しないときは、涼しく乾燥した場所に保管してください。
- Regularly check the antenna wire for any cuts, kinks, or damage. A damaged antenna can significantly reduce range.
- 受信機へのすべての接続が安全であり、腐食がないことを確認してください。
トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| バインドを試行した後、受信機の LED が点灯しません。 | Binding procedure not followed correctly; transmitter not in bind mode; bind plug not inserted correctly; power issue. | Repeat binding steps carefully. Ensure bind plug is fully inserted into Channel 3. Check power supply to receiver. Refer to transmitter manual for its specific binding process. |
| モデルからの応答がありません。 | Receiver not bound; transmitter off; low battery in transmitter or model; incorrect wiring; damaged receiver/servo/ESC. | Verify receiver is bound (solid LED). Ensure transmitter is on. Check battery levels. Inspect all wiring connections. Test components individually if possible. |
| 範囲が限られている、または信号が断続的。 | Antenna obstructed or damaged; interference; receiver mounted too close to metal/carbon fiber. | Ensure antenna is straight and clear of obstructions. Check for local interference sources. Relocate receiver if necessary. Inspect antenna wire for damage. |
| Failsafe not working. | Failsafe not set correctly; signal loss not detected. | Re-set the failsafe position following the instructions in the "Operating" section. Ensure the transmitter is turned off to test signal loss. |
保証とサポート
保証情報およびテクニカルサポートについては、Flyskyの公式ウェブサイトをご覧ください。 web詳細はウェブサイトをご覧いただくか、Flysky正規販売店にお問い合わせください。購入証明書として領収書を保管してください。