導入
This manual provides essential instructions for the setup, operation, and maintenance of your Pro-Ject RM 1.3 Turntable. Please read it thoroughly before use to ensure proper functionality and longevity of your device.
パッケージ内容
セットアップを続行する前に、すべてのコンポーネントが存在していることを確認してください。
- Pro-Ject RM 1.3 Turntable Unit
- 大皿
- ドライブベルト
- Outboard 15V AC Motor
- 電源
- Sumiko Pearl Cartridge (pre-installed or separate)
- Removable RCA Cables
- カウンターウェイト
- アンチスケーティングウェイト
- スタイラス圧力計
セットアップ手順
Follow these steps carefully to set up your turntable:
- 開梱: すべての部品をパッケージから慎重に取り出してください。将来の輸送に備えてパッケージは保管しておいてください。
- プラッターの取り付け: Place the platter onto the central spindle. Ensure it sits securely and rotates freely.
- モーターの配置: Position the outboard motor unit next to the turntable chassis. The motor pulley should align with the outer rim of the platter.
- Drive Belt Installation: Gently stretch the drive belt around the motor pulley and the outer rim of the platter. Ensure the belt is not twisted.
- Cartridge Installation (if not pre-installed): If your Sumiko Pearl cartridge is not pre-installed, carefully attach it to the tonearm headshell using the provided screws. Ensure correct alignment.
- カウンターウェイト調整: Slide the counterweight onto the rear of the tonearm. Adjust it until the tonearm floats horizontally. Then, set the tracking force according to the cartridge manufacturer's recommendations (typically 1.8g for Sumiko Pearl). Use a stylus pressure gauge for accuracy.
- アンチスケーティング調整: Attach the anti-skating weight to the tonearm's anti-skating mechanism. Adjust the setting to match the tracking force.
- 接続中 Amplifier： Connect the removable RCA cables from the turntable's output to the "Phono" input of your amplifier or a dedicated phono preamplifier. Ensure the ground wire is connected between the turntable and your amplifier / preampハムを最小限に抑えるリファイア。
操作手順
- 電源オン: Connect the power supply to the motor unit and a wall outlet. Press the power button on the motor unit to start the platter rotation.
- 速度を選択します: Most turntables offer 33 1/3 RPM and 45 RPM. Ensure the correct speed is selected for your record. (Refer to motor unit for speed selection mechanism, typically a switch or belt position change).
- 順位記録: ビニールレコードをプラッターの上に慎重に置きます。
- 下部トーンアーム: Gently lift the tonearm using the cueing lever. Position the stylus over the desired track on the record. Slowly lower the cueing lever to allow the stylus to descend onto the record groove.
- 再生： The record will now play. Adjust the volume on your amplifier。
- 再生を停止する: At the end of the record, or when you wish to stop, use the cueing lever to lift the tonearm from the record. Return the tonearm to its rest and secure it. Press the power button on the motor unit to stop the platter.
メンテナンス
- レコードクリーニング: Regularly clean your vinyl records using a dedicated record brush or cleaning solution to remove dust and static.
- スタイラスのケア: Use a soft stylus brush to gently clean the stylus tip before and after each play. Brush from back to front. Avoid touching the stylus with your fingers.
- ターンテーブルのクリーニング: Wipe the turntable chassis and platter with a soft, dry, lint-free cloth. Avoid abrasive cleaners or solvents.
- ベルトの検査: Periodically check the drive belt for wear or stretching. Replace if necessary to maintain accurate playback speed.
トラブルシューティング
ターンテーブルで問題が発生した場合は、次の一般的な問題と解決策を参照してください。
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| No power / Platter not spinning | Power cable disconnected; faulty power supply/motor; power outlet issue. | Ensure power cable is securely connected. Test the power outlet with another device. If the issue persists, contact support. |
| ハミング音またはブザー音 | Ground wire not connected; proximity to other electronics; faulty cabling; internal wiring issue. | Ensure the ground wire is securely connected between the turntable and amplifier / preamplifier. Move the turntable away from other electronic devices. Check RCA cables for damage. If hum persists, it may indicate an internal grounding issue requiring professional service. |
| Distorted sound / Skipping | Incorrect tracking force; worn or dirty stylus; damaged record; incorrect anti-skating. | Re-adjust tracking force and anti-skating. Clean the stylus. Inspect the record for damage. Replace stylus if worn. |
| 再生速度が正しくありません | Incorrect speed selection; worn or stretched drive belt. | Verify the correct speed setting. Inspect and replace the drive belt if it appears worn or loose. |
仕様
| 特徴 | 詳細 |
|---|---|
| ブランド | プロジェクト |
| モデル | RM 1.3 |
| 製品寸法 | 15 x 4.33 x 13.78インチ |
| アイテム重量 | 11.15ポンド |
| 含まれるコンポーネント | Sumiko Pearl Cartridge, removable RCA cables |
| モータータイプ | ACモーター |
| 信号フォーマット | アナログ |
| 巻tage | 15ボルト（AC） |
| 色 | 黒 |
保証とサポート
For warranty information, please refer to the documentation provided with your purchase or visit the official Pro-Ject website. For technical support or service inquiries, please contact your authorized Pro-Ject dealer or the manufacturer's customer service department.
保証請求に備えて購入証明書を保管してください。