SEM SEM-15003

SEM Products SEM-15003 Phantom White Color Coat

公式ユーザーマニュアル

導入

The SEM-15003 Phantom White Color Coat is a high-quality flexible coating designed to restore or change the color of various interior and exterior surfaces. This product is ideal for use on flexible and rigid plastics, carpet, and vinyl, providing a durable and long-lasting finish.

重要な安全情報:

DANGER! VAPOR HARMFUL. EXTREMELY FLAMMABLE LIQUID & VAPOR. VAPORS MAY CAUSE FLASH FIRE. CONTENTS UNDER PRESSURE. Read all cautions on the back panel before use.

Image of SEM Color Coat spray can, Phantom White, 12 oz.

This image displays the SEM Color Coat spray can in Phantom White. The label indicates it is a flexible coating designed to change or renew color on flexible and rigid plastics, carpet, and vinyl. The can also shows safety warnings regarding flammable liquid and vapor.

セットアップと表面の準備

Proper surface preparation is crucial for optimal adhesion and durability of the Color Coat. Follow these steps carefully:

  1. 表面をきれいにする: Thoroughly clean the surface to be coated with a suitable cleaner, such as SEM Soap or SEM Plastic & Leather Prep. Ensure all dirt, grease, oil, and contaminants are removed. Rinse thoroughly and allow to dry completely.
  2. Scuff the Surface: For best adhesion on rigid plastics and vinyl, lightly scuff the surface with a fine-grit abrasive pad (e.g., red scuff pad) or 400-600 grit sandpaper. This creates a mechanical bond.
  3. Adhesion Promoter (Optional but Recommended): For difficult-to-adhere plastics or vinyl, apply a thin, even coat of SEM Plastic Adhesion Promoter or SEM Vinyl Prep. Allow to flash off according to product instructions.
  4. マスキング： Mask off any areas not intended for coating using automotive-grade masking tape and paper.
  5. 換気： Ensure adequate ventilation in the work area. Use appropriate personal protective equipment, including a respirator, gloves, and eye protection.
  6. 温度： Apply in a well-ventilated area when air and surface temperatures are between 60°F (16°C) and 90°F (32°C).

操作（アプリケーションの説明）

Follow these instructions for applying SEM Color Coat:

  1. シェイク缶: Shake the aerosol can vigorously for at least one minute after the mixing ball begins to rattle. Continue to shake occasionally during application.
  2. テストスプレー: Before applying to the actual surface, test spray on an inconspicuous area or a piece of scrap material to check color match and spray pattern.
  3. 薄く塗る: Hold the can 8-10 inches from the surface. Apply several thin, even coats rather than one heavy coat. Applying heavy coats can lead to runs, drips, and poor adhesion.
  4. フラッシュ時間: Allow 5-10 minutes flash time between coats. The surface should appear dull before applying the next coat.
  5. Number of Coats: Typically, 2-3 light coats are sufficient to achieve full coverage and desired color. Additional coats may be applied for deeper color or increased durability.
  6. 乾燥時間:
    • Tack Free: Approximately 30 minutes.
    • Handleable: 1 hour.
    • Full Cure: 24 hours.
  7. 掃除： After use, invert the can and spray until only clear propellant comes out. This clears the nozzle and prevents clogging.

メンテナンス

Once fully cured, surfaces coated with SEM Color Coat are durable and easy to maintain.

  • クリーニング： Clean the coated surface with mild soap and water. Avoid harsh abrasive cleaners or solvents, as these can damage the finish.
  • 保護： For automotive interiors, consider using a UV protectant designed for vinyl and plastic to prolong the life and appearance of the coating.
  • 修理： Small scratches or scuffs can often be touched up with additional light coats of SEM Color Coat after proper cleaning and preparation of the affected area.

トラブルシューティング

問題考えられる原因解決
Poor Adhesion / PeelingImproper surface cleaning; surface not scuffed; no adhesion promoter used on difficult plastics.Ensure surface is meticulously clean and properly scuffed. Use an adhesion promoter if necessary.
ムラのある仕上がり/縞模様Applying too heavy coats; inconsistent spray distance; can not shaken enough.Apply multiple thin, even coats. Maintain consistent spray distance. Shake can thoroughly before and during use.
Runs / DripsApplying too heavy coats; holding can too close to surface.Apply lighter coats. Increase spray distance to 8-10 inches.
遅乾性High humidity; low temperature; poor ventilation; too heavy coats.Ensure proper ventilation and temperature. Apply thin coats.

仕様

  • 製品名: SEM Color Coat
  • モデル番号: SEM-15003
  • 色： Phantom White
  • 正味重量： 12オンス（340グラム）
  • メーカー: SEM Paints
  • 使用法： 屋内と屋外
  • Application Surfaces: Flexible and rigid plastics, carpet, vinyl.

保証とサポート

Specific warranty information for the SEM-15003 Phantom White Color Coat is provided by the manufacturer, SEM Paints. Please refer to the product packaging or contact SEM Paints directly for detailed warranty terms and conditions.

For technical support, product inquiries, or further assistance, please contact the manufacturer:

メーカー: SEM Paints

Contact details (e.g., website, phone number) are typically found on the product label or the manufacturer's official webサイト。

© 2023 SEM Products. All rights reserved.