導入
This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your E-flite Blade 3-Channel 2.4GHz Transmitter with Built-in LiPo Charger, model EFLRT324. Please read this manual thoroughly before using the product to ensure proper function and to prevent damage or injury. This transmitter is designed for use with compatible Blade remote-controlled aircraft and features an integrated LiPo battery charger.
製品終了view
Image: The E-flite Blade 3-Channel 2.4GHz Transmitter, showing its ergonomic design and control sticks. This image illustrates the primary device discussed in this manual.
設定
1. バッテリーの取り付けと充電
The transmitter requires a LiPo battery for operation. This unit includes a built-in charger for convenience.
- 初期費用： Before first use, fully charge the internal LiPo battery using the provided charging cable and a suitable USB power source. The charging indicator light will show the charging status (e.g., red for charging, green for fully charged).
- 航空機への接続: Ensure the aircraft's battery is charged and properly connected according to its specific manual.
2. 送信機と受信機のバインド
Binding establishes a unique communication link between your transmitter and the aircraft's receiver.
- 電源を切る： Ensure both the transmitter and the aircraft's receiver are powered off.
- Receiver Binding Mode: Follow the aircraft's manual to put its receiver into binding mode. This usually involves holding a button on the receiver while powering it on.
- Transmitter Binding Mode: While holding the bind button (if present) on the transmitter, power on the transmitter. Refer to the transmitter's specific diagram for the bind button location.
- 確認： The indicator lights on both the transmitter and receiver will typically change from flashing to solid, indicating a successful bind.
- テストコントロール: After binding, power cycle both devices and test all control surfaces and functions before flight.
オペレーティング
1.電源のオン/オフ
- 電源を入れるには: インジケーターライトが点灯するまで電源ボタンを押し続けます。
- 電源を切るには: Press and hold the power button until the indicator light turns off. Always power off the aircraft first, then the transmitter.
2. 基本的な操作
This 3-channel transmitter typically controls the following functions:
- Channel 1 (Aileron/Roll): Controls the aircraft's roll movement.
- Channel 2 (Elevator/Pitch): Controls the aircraft's pitch movement.
- Channel 3 (Throttle/Rudder): Controls motor speed (throttle) or yaw movement (rudder), depending on aircraft configuration.
Familiarize yourself with the stick movements and their corresponding aircraft responses in a safe, open area before attempting flight.
3. Using the Built-in LiPo Charger
The transmitter features a built-in charger for compatible LiPo batteries, typically those used in ultra-micro aircraft.
- バッテリーを接続します: Plug the small LiPo battery into the designated charging port on the transmitter. Ensure correct polarity.
- 充電インジケーター: The charging indicator light will activate (e.g., red) to show charging is in progress.
- 充電完了: The light will change (e.g., green or off) when the battery is fully charged. Disconnect the battery promptly.
Caution: Only charge compatible LiPo batteries. Charging incompatible batteries or incorrect polarity can cause fire or damage.
メンテナンス
1. 清掃
- Wipe the transmitter with a soft, dry cloth.
- 溶剤や研磨剤入りのクリーナーは使用しないでください。
- Keep dust and debris out of the stick gimbals and buttons.
2. ストレージ
- 送信機は、直射日光や極端な温度を避け、涼しく乾燥した場所に保管してください。
- Remove any external batteries if storing for extended periods (though this model has an internal LiPo).
- Ensure the internal LiPo battery is stored at a "storage charge" level (typically 3.8V per cell) if not used for several weeks. Refer to LiPo battery safety guidelines.
トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| 送信機の電源が入りません。 | Internal LiPo battery is discharged. | Charge the transmitter's internal LiPo battery. |
| 航空機は制御に反応しません。 | Not bound to receiver; receiver not powered; incorrect model memory selected (if applicable). | Perform binding procedure again. Ensure receiver has power. |
| 制御範囲が短い、または信号が断続的です。 | 干渉、アンテナの損傷、送信機の電池残量低下。 | Operate in an open area away from obstacles and other 2.4GHz devices. Check antenna for damage. Charge transmitter battery. |
| Built-in charger not working. | Incorrect battery connected; faulty charging cable/port. | Ensure only compatible LiPo batteries are connected with correct polarity. Try a different USB power source or cable. |
仕様
- ブランド： E-FLITE
- モデル名: EFLRT324
- チャンネル: 3チャンネル
- 頻度： 2.4GHz
- 特集: Wireless, Built-in LiPo Charger
- 商品の寸法 (長さ x 幅 x 高さ): 8.1 x 6.6 x 5.4インチ
- 国際コード: 605482052549
- メーカー部品番号: EFLRT324
保証とサポート
E-flite products are designed for quality and performance. For specific warranty information, please refer to the warranty card included with your product or visit the official E-flite website. For technical support, troubleshooting assistance beyond this manual, or replacement parts, please contact E-flite customer service.
保証請求のために購入証明書を保管してください。