TC Electronic NM-1 Nova Modulator User Manual

1. はじめに

The TC Electronic NM-1 Nova Modulator is a versatile dual modulation effects pedal designed for guitarists. It offers a wide range of modulation effects, including chorus, flanger, phaser, tremolo, and vibrato, with independent control over two effect engines (A and B). This manual will guide you through the setup, operation, and maintenance of your device.

2.製品オーバーview

図1: TC Electronic NM-1 Nova Modulator. This image displays the top panel of the pedal, highlighting the various knobs, buttons, and footswitches for controlling the dual modulation effects.

コントロールとコネクタ

The NM-1 Nova Modulator features a comprehensive set of controls for precise sound shaping. Refer to Figure 1 for visual identification of the following components:

• 電源入力: 付属の電源アダプターに接続します。
• 入出力ジャック： Standard 1/4-inch mono or stereo jacks for audio signal.
• フットスイッチ:
  • オン/オフフットスイッチ: Activates or bypasses the overall effect. Holding it allows manual/preset switching.
  • TEMPO Footswitch: Used for tap tempo input. Holding it allows calibration.
• Effect Select Buttons (A/B): Selects the modulation type for each engine (Chorus, Tri-Chorus, Flanger, Phaser, Tremolo, Vibrato).
• Variation Buttons (+variation): Adds variations to the selected effect.
• コントロールノブ： Adjust parameters such as Speed, Depth, Feedback, Mix, and LFO Sync.
• 画面： A numerical display shows current settings or tempo.

3. セットアップ

3.1 開梱

Carefully remove the Nova Modulator from its packaging. Ensure all components are present: the pedal unit, power adapter, and this user manual.

3.2電源接続

Connect the supplied power adapter to the DC input jack on the rear of the Nova Modulator. Plug the adapter into a suitable power outlet. Use only the original TC Electronic power supply to prevent damage and ensure optimal performance.

3.3オーディオ接続

The Nova Modulator supports both mono and stereo operation.

• モノラル設定: 楽器を Input L (Mono) ジャックに接続します Output L (Mono) あなたのジャックに ampリファイアーまたは次のエフェクトペダル。
• ステレオ設定: 楽器を Input L (Mono) jack. If using a stereo source, connect both 入力L そして 入力抵抗。 接続します 出力L そして 出力R ステレオへのジャック ampリバーシ設定やその他のステレオ効果。

3.4初期電源オン

Once all connections are made, ensure power is supplied. The display will illuminate, indicating the unit is ready for use.

4. 操作手順

4.1 Activating/Bypassing Effects

を押す オン/オフ footswitch to toggle the overall effect on or off. The corresponding LED will indicate the status.

4.2 Selecting Modulation Effects (Engine A & B)

The Nova Modulator features two independent modulation engines, A and B.

• For Engine A, use the エフェクトA buttons to select between Chorus, Tri-Chorus, Flanger, Phaser, Tremolo, or Vibrato.
• For Engine B, use the エフェクトB buttons to select between Chorus, Tri-Chorus, Flanger, Phaser, Tremolo, or Vibrato.
• を押す +variation button for each engine to access alternative variations of the selected effect type.

4.3 パラメータの調整

Use the dedicated control knobs to fine-tune the parameters of the selected effects:

• スピード： Controls the rate of the modulation.
• 深さ： Adjusts the intensity or range of the modulation.
• フィードバック： (For Flanger/Phaser) Controls the amount of effect signal fed back into the input.
• ミックス： Blends the dry (unaffected) signal with the wet (effected) signal.
• LFO Sync: Synchronizes the Low-Frequency Oscillator (LFO) to the tempo.
• フィルター： Shapes the tone of the modulated signal.

4.4 Tempo Control

タップして テンポ footswitch two or more times to set the tempo for time-based effects. The tempo LED will flash to indicate the current tempo.

4.5 プリセット管理

The Nova Modulator allows you to store and recall your favorite settings.

• プリセットの保存: Adjust your desired settings. Hold the PRESET HOLD to store button until the display confirms the preset is saved.
• プリセットの呼び出し: 短く押すと プリセット 保存されているプリセットを循環するボタン。
• 手動モード: 保持する オン/オフ footswitch to switch between manual mode (current knob settings) and preset mode.

5. メンテナンス

5.1 クリーニング

To clean the unit, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or waxes, as these can damage the finish and internal components. Ensure the unit is powered off and disconnected from the power source before cleaning.

5.2 ストレージ

When not in use for extended periods, store the Nova Modulator in a cool, dry place, away from direct sunlight and extreme temperatures. It is recommended to keep the original packaging for protection during storage or transport.

5.3ファームウェアアップデート

Periodically check the official TC Electronic website for any available firmware updates. Follow the instructions provided on the website for updating your device. Firmware updates can introduce new features, improve performance, or fix bugs.

6。 トラブルシューティング

If you encounter issues with your Nova Modulator, refer to the following common problems and solutions:

• 音が出ない:
  • 電源アダプタがしっかりと接続され、ユニットの電源がオンになっていることを確認します。
  • すべてのオーディオ ケーブルが正しく接続され、整合性があるかどうかを確認します。
  • 確認する オン/オフ footswitch is engaged (effect LED is lit).
  • チェックしてください ミックス knob setting; if set to fully dry, no effect will be heard.
• 効果は変化しない:
  • Ensure you are in manual mode if you expect knob changes to take immediate effect.
  • Verify that the correct effect engine (A or B) is selected for adjustment.
• 不要なノイズ/ハム音:
  • Ensure you are using the original power adapter.
  • 別の電源コンセントを試してください。
  • Check for ground loops in your audio chain.
• フットスイッチが反応しない:
  • ユニットの電源を入れ直します。
  • Ensure no debris is obstructing the footswitch mechanism.

7. 仕様

8. 保証情報

TC Electronic products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please refer to the warranty card included with your product or visit the official TC Electronic webサイトでご確認ください。保証請求に備えて購入証明書を保管してください。

9. カスタマーサポート

For technical assistance, product inquiries, or service requests, please contact TC Electronic customer support. You can find contact information, FAQs, and additional resources on the official TC Electronic webサイト： www.tcelectronic.com. Please have your product model and serial number ready when contacting support.