1. はじめに
The Woods 59408WD Outdoor Hard-Wired Post Eye Light Control is designed to automatically turn your outdoor lighting on at dusk and off at dawn. This photocell light sensor provides reliable, energy-efficient control for various outdoor light fixtures, ensuring your property is illuminated when needed without manual intervention. It is suitable for hard-wired installations in appropriate enclosures.
2. 安全情報
- 警告： 感電の危険があります。設置やメンテナンスを行う前に、回路ブレーカーまたはヒューズボックスの電源を切ってください。
- This device is intended for installation in accordance with the National Electrical Code and local regulations. If you are unsure about wiring, consult a qualified electrician.
- Ensure the device is installed in a dry location or within a weather-resistant enclosure to prevent water damage and ensure safe operation.
- 指定された電気定格を超えないでください。
3. パッケージ内容
- Woods 59408WD Photocell Light Control
- Hardwire Black (integrated wiring)
4. 仕様
| ブランド | ウッズ |
| モデル番号 | 59408WD |
| 巻tage | 120ボルト |
| ワットtage | 1800ワット（最大） |
| 制御方法 | Photocell (Dusk-to-Dawn) |
| スイッチタイプ | ハードワイヤード |
| 屋内/屋外での使用 | Indoor, Outdoor (in dry location/enclosure) |
| Light Source Compatibility | Fluorescent, Halogen, Incandescent, LED |
| 寸法（長さ×幅×高さ） | 長さ1.8インチ x 幅1.1インチ x 高さ2.1インチ |
| 重さ | 0.11 ポンド |
5. インストール
5.1 必要なツール
- ドライバー
- ワイヤストリッパ
- Wire nuts (appropriate size)
- 電気テープ
- 巻tageテスター
- Weather-resistant electrical enclosure (if installing outdoors in an exposed location)
5.2配線手順
重要： 取り付けを始める前に、回路ブレーカーの電源がオフになっていることを確認してください。
- ワイヤーを準備する： Strip approximately 1/2 inch of insulation from the ends of all wires (photocell, incoming power, and light fixture wires).
- 中性線を接続する: 接続する 白いワイヤー from the photocell to the incoming 白（中性）線 from your power source and the 白（中性）線 of your light fixture. Secure with a wire nut.
- Connect Line (Hot) Wire: 接続する 黒線 from the photocell to the incoming black (hot/line) wire from your power source. Secure with a wire nut.
- 負荷線を接続: 接続する 赤いワイヤー from the photocell to the black (hot/load) wire of your light fixture. Secure with a wire nut.
- 安全な接続: Ensure all wire nuts are tight and connections are secure. Wrap each wire nut with electrical tape for added insulation and protection.
- Mount Photocell: Mount the photocell in a location where it will receive natural daylight and is not obstructed by shadows or artificial light sources (e.g., other lights, car headlights) that could interfere with its operation. If installing outdoors, ensure it is within a suitable weather-resistant enclosure.
- 電力を回復する： Once all connections are secure and the photocell is mounted, restore power at the circuit breaker.
注記： The photocell may have a built-in delay (typically a few seconds to a few minutes) before activating or deactivating to prevent false triggers from transient light changes.
Image: The Woods 59408WD Post Eye Light Control, a compact black unit with a visible light sensor on the front.
画像: クローズアップ view of the photocell sensor on the Woods 59408WD unit, showing the light-sensitive element.
6. 操作
The Woods 59408WD Post Eye Light Control operates automatically based on ambient light levels:
- At Dusk: When natural light levels fall below a certain threshold, the photocell will detect darkness and activate the connected light fixture.
- At Dawn: When natural light levels rise above a certain threshold, the photocell will detect sufficient light and deactivate the connected light fixture.
There is an intentional delay in the switching mechanism (typically a few seconds to a few minutes) to prevent the light from cycling on and off due to temporary shadows, car headlights, or lightning flashes.
7. メンテナンス
The Woods 59408WD Post Eye Light Control requires minimal maintenance:
- Periodically inspect the photocell sensor for any dirt, dust, or debris that might obstruct its view of ambient light. Gently clean the sensor with a soft, damp 必要に応じて布で覆います。
- Ensure the area around the sensor remains clear of obstructions (e.g., growing foliage, new decorations) that could block natural light.
- Check wiring connections annually for any signs of wear or corrosion, especially in outdoor installations.
8。 トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| ライトは継続的に点灯します。 | Sensor is not receiving enough light (e.g., obstructed, installed in a dark area). Wiring error (e.g., load wire connected to line). Defective photocell. | Relocate or clear obstructions from the sensor. Verify wiring connections according to Section 5.2. Consult an electrician if unsure. Replace the photocell if other solutions fail. |
| 夕暮れ時にライトは点灯しません。 | ユニットに電源が供給されていません。 Sensor is receiving too much light (e.g., from another light source). 配線エラー。 Defective photocell or light fixture bulb. | 回路ブレーカーと電源を確認してください。 Relocate the sensor or shield it from artificial light sources. Verify wiring connections according to Section 5.2. Test the light fixture with a different power source or replace the bulb. Replace photocell if necessary. |
| Light cycles on/off rapidly. | Interference from flickering light sources or transient shadows. Sensor is partially obstructed or dirty. | Ensure the sensor has a clear, consistent view of ambient light. Clean the sensor. Note that a short delay is normal to prevent rapid cycling. |
| Light turns on/off with a delay. | これは正常な動作です。 | The photocell is designed with a built-in time delay to prevent false triggers. This is not a malfunction. |
9. 保証とサポート
For warranty information or technical support, please refer to the product packaging or contact Woods customer service directly. Keep your purchase receipt as proof of purchase.