Intermec EasyCoder PF4i Printer Instruction Manual

導入

This manual provides essential instructions for the setup, operation, and maintenance of your Intermec EasyCoder PF4i Direct Thermal/Thermal Transfer Label Printer. Please read this manual thoroughly before using the printer to ensure proper functionality and to prevent damage.

The Intermec EasyCoder PF4i is designed for reliable monochrome label printing, supporting both direct thermal and thermal transfer printing methods with a resolution of 203 DPI.

設定

1.プリンターの開梱

• プリンターとすべての付属品をパッケージから慎重に取り出します。
• Verify that all components are present: printer unit, power cord, and any included cables or documentation.
• 将来の輸送や保管のために、元の梱包を保管してください。

2. 電源の接続

Connect the power cord to the printer's power input port and then to a grounded electrical outlet. Ensure the power switch is in the OFF position before connecting the power cord.

画像: 背面 view of the Intermec EasyCoder PF4i printer. This image displays the power input, the main power switch, and various connectivity ports including USB-C, serial, and Ethernet.

3. コンピュータへの接続

The PF4i printer supports USB-C connectivity. Connect one end of the USB-C cable to the printer's USB-C port and the other end to your computer. Install the necessary printer drivers as per the instructions provided with your operating system or from the Intermec support webサイト。

4. Loading Print Media (Labels)

The Intermec EasyCoder PF4i is designed to print on labels. Follow these steps to load the label roll:

1. プリンターの上部カバーを開きます。
2. Place the label roll onto the media supply spindle, ensuring the labels feed from the bottom of the roll.
3. Thread the leading edge of the labels through the print mechanism, past the print head, and under the platen roller.
4. メディア ガイドを調整して、動きを制限せずにラベルの幅にぴったり合うようにします。
5. 上カバーをしっかりと閉めてください。

画像: 内部 view of the Intermec EasyCoder PF4i printer with the top cover open. This image illustrates the path for loading label media and the location of the print head and platen roller.

5. 初期設定

After connecting the printer and loading media, power on the printer using the main power switch. The printer may perform a self-test. Use the push button controls on the printer or the dedicated app to configure basic settings such as media type, print darkness, and calibration.

操作手順

1. Printing a Label

Once the printer is set up and connected to your computer, you can initiate print jobs from your label design software or application. Ensure the correct printer driver is selected and that the label dimensions in your software match the physical labels loaded in the printer.

• ラベルデザインソフトウェアまたはアプリケーションを開きます。
• Create or open the label design you wish to print.
• Go to the print dialog (usually File > 印刷）。
• Select the "Intermec EasyCoder PF4i" as your printer.
• Adjust any print settings as needed (e.g., number of copies, print speed, darkness).
• 「印刷」をクリックします。

2. Direct Thermal vs. Thermal Transfer Printing

The PF4i supports both direct thermal and thermal transfer printing:

• Direct Thermal: This method uses heat-sensitive labels that darken when heated by the print head. No ribbon is required. Labels printed with this method are generally suitable for short-term use as they can fade over time or with exposure to heat/light.
• Thermal Transfer: This method uses a ribbon that is melted onto the label by the print head, creating a durable, long-lasting image. This method requires both labels and a thermal transfer ribbon.

Select the appropriate printing method in your printer driver settings or through the printer's control panel/app, depending on the type of labels and ribbon (if any) you are using.

メンテナンス

定期的なメンテナンスにより、最適なパフォーマンスが確保され、プリンターの寿命が延びます。

1. プリントヘッドのクリーニング

The print head should be cleaned regularly, especially if print quality degrades or after changing label rolls. Use a lint-free cloth moistened with isopropyl alcohol (99% pure) or a specialized print head cleaning wipe.

1. プリンタの電源をオフにして、電源コードを取り外します。
2. プリントヘッドにアクセスするには、上部カバーを開きます。
3. Gently wipe the print head surface from one end to the other. Avoid touching the print head with bare hands.
4. カバーを閉じて電源を再接続する前に、プリント ヘッドが完全に乾くまでお待ちください。

2. プラテンローラーのクリーニング

The platen roller can accumulate adhesive residue or dust. Clean it with a lint-free cloth moistened with isopropyl alcohol.

1. プリンタの電源をオフにして、電源コードを取り外します。
2. 上部カバーを開きます。
3. Rotate the platen roller manually while wiping its surface to remove any debris.
4. Allow it to dry before use.

3. 消耗品の交換

Replace label rolls and thermal transfer ribbons (if used) as they run out. Refer to the "Loading Print Media" section for instructions on replacing labels. For thermal transfer printing, ensure the ribbon is correctly installed according to the printer's internal diagrams or specific instructions.

トラブルシューティング

This section addresses common issues you might encounter with your Intermec EasyCoder PF4i printer.

電源なし

• 電源コードがプリンタと正常な電源コンセントの両方にしっかりと接続されていることを確認します。
• Check the power switch on the back of the printer is in the ON position.

印刷出力なし

• Verify that the printer is powered on and connected to the computer.
• Check if labels are loaded correctly and that the media guides are properly adjusted.
• If using thermal transfer, ensure the ribbon is correctly installed and not depleted.
• Confirm that the correct printer driver is selected in your software and that the print job is not paused or stuck in the print queue.
• Perform a printer self-test (refer to the printer's control panel or app for instructions) to rule out software issues.

Poor Print Quality (Faint, Streaky, or Missing Areas)

• 「メンテナンス」セクションの説明に従ってプリントヘッドをクリーニングします。
• Adjust the print darkness setting in your printer driver or via the printer's controls.
• Ensure you are using compatible labels and, if applicable, a compatible thermal transfer ribbon.
• Check for any physical damage to the print head or platen roller.

接続の問題

• Ensure the USB-C cable is securely connected at both ends.
• Try using a different USB-C port on your computer or a different cable.
• Reinstall the printer drivers if they appear corrupted or outdated.

仕様

保証情報

Intermec products typically come with a standard manufacturer's warranty. For specific details regarding the warranty period and terms for your EasyCoder PF4i printer, please refer to the warranty card included with your product or visit the official Intermec (now Honeywell) support webサイトでご確認ください。保証請求に備えて購入証明書を保管してください。

サポートとお問い合わせ

For technical assistance, driver downloads, or further support, please visit the official support website for Intermec products (now part of Honeywell). You can typically find FAQs, troubleshooting guides, and contact information for customer service there.

When contacting support, please have your printer's model number (PF4ID00100000020) and serial number ready.