Clover B14A Hot and Cold Bottled Water Dispenser User Manual

1. はじめに

The Clover B14A Hot and Cold Bottled Water Dispenser provides convenient access to refreshing chilled drinking water and piping hot water. Designed for home or office use, this dispenser features hygienic stainless steel tanks and an efficient cooling and heating system. Please read this manual thoroughly before operation to ensure safe and optimal performance.

2. 安全情報

• 電気安全: This appliance operates on 110-120 volts, 50-60 Hz. Ensure the power outlet is properly grounded. Do not use with damaged cords or plugs.
• お湯の安全性: The hot water temperature reaches approximately 185°F (85°C). Exercise extreme caution when dispensing hot water to prevent burns. A safety switch is provided for the hot water dispenser.
• 子どもの安全: Always engage the hot water safety switch when children are present to prevent accidental dispensing of hot water.
• 配置: Place the dispenser on a flat, stable surface away from direct sunlight, heat sources, and areas with high humidity. Ensure adequate ventilation around the unit.
• 水のボトル： Use only standard 5-gallon (18.9-liter) water bottles.
• メンテナンス： 清掃やメンテナンスを行う前に、ユニットのプラグを抜いてください。

3. セットアップ

1. 開梱: ディスペンサーをパッケージから慎重に取り出し、損傷がないか確認してください。
2. 配置: Position the dispenser on a level, sturdy surface. Allow at least 4 inches (10 cm) of clearance from walls for proper ventilation.
3. ドリップトレイの取り付け: Insert the concealed, lift-out drip tray into its designated slot below the spigots.
4. 初期クリーニング: Before first use, clean the exterior with a soft, damp 布。
5. ウォーターボトルの取り付け: Remove the protective seal from a new 5-gallon water bottle. Lift the bottle and quickly invert it, placing it firmly onto the bottle support on top of the dispenser. Ensure the bottle is seated correctly to prevent leaks.
6. フラッシュシステム: Before plugging in, dispense at least 1 liter (approximately 4 cups) of water from both the hot and cold spigots to ensure the tanks are filled and to flush any air from the system.
7. プラグイン: 電源コードをアース付き 110 ～ 120V 電源コンセントに差し込みます。

図1：フル view of the Clover B14A water dispenser with a 5-gallon bottle.

4. 操作手順

1. 電源オン: Once plugged in, the dispenser will begin cooling and heating the water. Allow approximately 15-30 minutes for the water to reach desired temperatures.
2. 冷水を出す: Place your cup under the cold water spigot (typically blue). Push the lever to dispense cold water. Release the lever to stop.
3. お湯の供給: Place your cup under the hot water spigot (typically red). To dispense hot water, first push the safety switch (often a red button or lever) and then push the main lever. Release both to stop.
4. 温水スイッチ: The hot water function can be turned on or off using the switch located on the back of the unit. Turning it off will prevent the water from heating, saving energy and acting as an additional safety measure.
5. Adjusting Cold Water Temperature: The cold water temperature can be adjusted via a thermostat control, usually located on the back of the unit. It allows for a range of 35.6°F to 53.6°F (2°C to 12°C).

Figure 2: Detail of the hot (red) and cold (blue) water spigots with the hot water safety switch.

5. メンテナンス

• ドリップトレイのクリーニング: The drip tray is removable for easy cleaning. Periodically empty and wash the tray with mild soap and water.
• 外装清掃: 外側の表面を柔らかい布で拭きます。amp 布で拭いてください。研磨剤や溶剤は使用しないでください。
• スケール除去： Over time, mineral deposits may accumulate in the hot water tank. Consult the manufacturer's web推奨されるスケール除去手順については、サイトまたはカスタマー サポートにお問い合わせください。
• 水タンクのクリーニング: For thorough cleaning of the internal water tanks, it is recommended to contact a qualified service technician.

6。 トラブルシューティング

• 給水なし: Ensure the water bottle is properly seated and not empty. Check if the unit is plugged in and powered on.
• お湯なし： Verify the hot water switch on the back of the unit is in the 'ON' position. Check if the thermal reset button (often a small red button on the back) needs to be pressed.
• No Cold Water: Ensure the unit is plugged in and the cold water thermostat is set to a desired temperature.
• 漏れ: Check the water bottle for cracks or improper seating. Ensure the drip tray is correctly installed.
• 異常なノイズ: The unit is designed for quiet operation. If unusual or excessive noise occurs, ensure the unit is on a level surface and not vibrating against a wall. If noise persists, contact customer support.

7. 仕様

• モデル： B14A
• 寸法 (奥行×幅×高さ): 12.3インチ x 12.7インチ x 37.9インチ (31.2 cm x 32.3 cm x 96.3 cm)
• 重さ： 32ポンド（14.5kg）
• 色： Black with Steel side panels
• 巻tage: 110-120V
• 頻度： 50～60Hz
• お湯の温度： Approximately 185°F (85°C) (non-adjustable)
• 冷水温度： 35.6°F - 53.6°F (2°C - 12°C) (adjustable)
• 対応ボトルサイズ: 5ガロン（18.9リットル）
• 建設資材: ステンレス、プラスチック
• 認定: CE, NSF, UL, Energy Star Rated
• 受け皿： Concealed, lift-out design, high impact, durable ABS. Removable, anti-splash grid.

8. 保証とサポート

The Clover B14A Hot and Cold Bottled Water Dispenser comes with a 1年間のメーカー限定保証. For warranty claims, technical assistance, or further inquiries, please contact Clover customer support. Keep your purchase receipt as proof of purchase.