導入
The E-flite EFLA600 Universal Light Kit Controller is designed to provide remote control functionality for LED lighting systems on remote-controlled aircraft. This controller enables users to activate and deactivate connected LED lights via an auxiliary channel on their RC receiver, enhancing visibility and realism for various RC models.
安全上の注意
- Always disconnect power from your RC system before making any electrical connections or disconnections to prevent damage to components or injury.
- 入力ボリュームがtage to the controller does not exceed 5.5ボルト. Exceeding this voltagコントローラーが損傷します。
- Verify correct polarity when connecting LED lights to the controller outputs. Incorrect polarity can damage the LEDs or the controller.
- Keep the controller and all electrical components away from moisture and extreme temperatures.
- This product is intended for use with E-flite Universal Light Kit LEDs. Compatibility with other LED types is not guaranteed.
セットアップとインストール
Follow these steps to properly install and connect your E-flite EFLA600 Universal Light Kit Controller:
- 受信機に接続します: Plug the controller's servo lead (the three-wire connector) into an available auxiliary channel on your RC receiver. This channel will be used to control the ON/OFF function of the lights.
- LEDライトを接続する: Connect your E-flite Universal Light Kit LEDs to the white JST-style output ports on the controller. The controller supports up to 16 individual LEDs. Ensure each LED string is securely connected.
- 電源: The controller draws power directly from the receiver. Ensure your receiver's power supply (e.g., BEC from an ESC or a separate receiver battery) can provide sufficient current for the controller and all connected LEDs.
This image shows the E-flite EFLA600 Universal Light Kit Controller. It is a small, black rectangular unit with the E-flite logo and product information printed on it. Wires extend from both ends: one end has a standard servo connector for receiver input, and the other end has four white JST-style connectors for attaching LED light strings.
操作手順
The E-flite EFLA600 controller operates by interpreting the pulse width signal from your receiver's auxiliary channel.
- ON Function: The LED lights will turn ON when the pulse width from the receiver channel is greater than 1.5 milliseconds (> 1.5ms).
- オフ機能: The LED lights will turn オフ when the pulse width from the receiver channel is less than 1.5 milliseconds (< 1.5ms). This typically corresponds to approximately the middle stick position on your transmitter for a two-position switch or a specific range for a proportional channel.
Average Current Load
The current draw depends on the number of connected LEDs:
- 6つのLED： Approximately 60mA @ 5.5 volts
- 12つのLED： Approximately 120mA @ 5.5 volts
- 16つのLED： Approximately 160mA @ 5.5 volts
Ensure your receiver's power source can adequately supply this current without voltage drops, especially when operating other servos or components.
メンテナンス
The E-flite EFLA600 Universal Light Kit Controller requires minimal maintenance to ensure long-term performance:
- クリーニング： Keep the controller free from dust, dirt, and debris. Use a soft, dry cloth to gently wipe the unit if necessary. Avoid using solvents or harsh chemicals.
- 検査： Periodically inspect all wiring and connectors for signs of wear, damage, or corrosion. Ensure all connections are secure.
- ストレージ： When not in use, store the controller in a cool, dry environment, away from direct sunlight and extreme temperatures.
トラブルシューティング
If you encounter issues with your E-flite EFLA600 controller, refer to the following troubleshooting guide:
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Lights do not turn ON/OFF | Incorrect receiver channel connection or assignment. Transmitter switch/stick position incorrect. Controller damaged. | Verify the servo lead is connected to an active auxiliary channel. Check transmitter settings for the assigned channel. Ensure the switch/stick moves past the 1.5ms threshold. |
| 照明がちらついたり暗くなったりする | Loose connections. Insufficient power from receiver. Damaged LEDs. | Check all LED and receiver connections for security. Ensure receiver power supply can handle the current load. Test LEDs individually if possible. |
| コントローラーが応答しない | 入力ボリュームtage out of range. Controller damaged. | 入力ボリュームを確認するtage is between 3V and 5.5V. If voltage is correct and connections are secure, the controller may be damaged and require replacement. |
| 一部のLEDのみが点灯します | Faulty LED string. Loose connection to a specific LED port. | Check connections for the non-working LEDs. Test individual LED strings if possible to identify faulty units. |
仕様
| 特徴 | 仕様 |
|---|---|
| モデル番号 | EFLA600 |
| 入力ボリュームtage | 3 – 5.5 Volts DC (Do not exceed 5.5V) |
| Max LED Capacity | Up to 16 E-flite Universal Light Kit LEDs |
| オン/オフ制御 | Via RC receiver auxiliary channel |
| Activation Threshold | ON at > 1.5ms pulse width, OFF at < 1.5ms pulse width |
| Average Current Load (6 LEDs) | 60mA @ 5.5V |
| Average Current Load (12 LEDs) | 120mA @ 5.5V |
| Average Current Load (16 LEDs) | 160mA @ 5.5V |
| 材質タイプ | プラスチック |
| アイテム重量 | 0.02ポンド（約9グラム） |
| アイテムの寸法 | 4 x 2.4 x 0.27インチ（約10.16 x 6.1 x 0.69 cm） |
| 原産国 | 中国 |
保証情報
For detailed warranty information regarding your E-flite EFLA600 Universal Light Kit Controller, please refer to the warranty documentation provided with your purchase or visit the official E-flite webサイトをご覧ください。保証条件は地域や販売店によって異なる場合があります。
サポート
If you require further assistance or have questions not covered in this manual, please contact E-flite customer support or visit their official web追加のリソース、FAQ、および連絡先情報については、サイトをご覧ください。
E-flite Official Webサイト： www.e-fliterc.com