15 Amp ルーター速度制御取扱説明書

製品終了view

この15 Amp Router Speed Control is designed to convert a single-speed router into a variable speed router. It is compatible with any universal AC/DC motor, allowing for precise control over motor speed for various applications.

主な特徴:

• Dial controls the variable speed (high, medium or low)
• 3-way rocker switch for operation modes
• 6 ft. cord for flexible placement

重要な情報:

• 最大ワットtage：1800ワット
• 入力ボリュームtage：120ボルト
• 最大 Amp年齢: 15 Amps

製品構成

画像: 正面 view 15の Amp Router Speed Control. It features a black rectangular housing with a white faceplate. On the faceplate, there is a black 3-way rocker switch labeled "VAR OFF FULL" at the top. Below it, a large black rotary dial with a silver center is visible, marked with green (M for Medium) and red (H for High) sections. At the bottom of the faceplate, text indicates "INPUT V. MAX A." and "120 V 15 A." A black power cord extends from the bottom of the unit.

The speed control unit consists of a durable housing, a variable speed dial, a 3-way rocker switch, and an integrated power cord.

設定

1. 開梱と検査： Carefully remove the speed control from its packaging. Inspect the unit for any signs of damage during shipping. Do not use the device if any damage is observed.
2. 電源要件: Ensure the power outlet you intend to use provides 120 volts AC. The speed control is rated for a maximum of 15 Amps and 1800 watts. Do not exceed these ratings.
3. Connecting the Tool: Plug your universal AC/DC motor tool (e.g., router) directly into the receptacle on the speed control unit.
4. 電源への接続: Plug the speed control's 6 ft. cord into a standard 120V AC electrical outlet.
5. 配置: Place the speed control on a stable, dry surface, away from moisture and heat sources. Ensure adequate ventilation around the unit.

安全警告: Always ensure the tool connected to the speed control is switched off before plugging it into the speed control unit or the wall outlet. Disconnect power before making any adjustments or performing maintenance.

操作手順

15人 Amp Router Speed Control offers three operational modes via its 3-way rocker switch and a variable speed dial for precise adjustments.

1. Understanding the 3-Way Rocker Switch:
   • "VAR" (Variable): In this position, the speed of the connected tool is controlled by the rotary dial. This allows for fine-tuning the motor's RPM.
   • "OFF": This position completely cuts power to the connected tool. Always switch to "OFF" when not in use or before disconnecting.
   • "FULL": In this position, the connected tool receives full line voltage, bypassing the variable speed control. The tool will operate at its maximum speed.
2. Adjusting Speed with the Dial: When the rocker switch is in the "VAR" position, rotate the large black dial to adjust the motor speed. Turning the dial clockwise typically increases speed, and counter-clockwise decreases it. The dial has markings (e.g., M for Medium, H for High) to guide speed selection.
3. 操作の開始:
   • Ensure the tool connected to the speed control is in its "OFF" position.
   • Set the speed control's rocker switch to "VAR" or "FULL" as desired.
   • Turn on the connected tool. Adjust the speed dial if in "VAR" mode to achieve the desired RPM.
4. 停止操作:
   • Turn off the connected tool.
   • Set the speed control's rocker switch to "OFF".
   • For extended periods of non-use, unplug the speed control from the wall outlet.

注意： Some tools may not operate efficiently at very low speeds. Refer to your tool's manual for recommended operating speeds. Do not use this speed control with tools that draw more than 15 Ampsまたは1800ワット。

メンテナンス

Proper maintenance ensures the longevity and safe operation of your speed control unit.

• クリーニング： Disconnect the speed control from the power source before cleaning. Use a soft, dry cloth to wipe down the exterior. Do not use abrasive cleaners, solvents, or immerse the unit in water.
• ストレージ： When not in use, store the speed control in a clean, dry place, away from direct sunlight, extreme temperatures, and moisture. Coil the power cord neatly to prevent kinks or damage.
• コード検査： Regularly inspect the power cord and plug for any signs of damage, cuts, or fraying. If damage is found, discontinue use immediately and have it repaired by a qualified technician.

トラブルシューティング

If you encounter issues with your 15 Amp Router Speed Control, refer to the following common problems and solutions:

For issues not listed above, or if solutions do not resolve the problem, please contact Harbor Freight Tools customer support.

仕様

保証とサポート

保証情報:

For detailed warranty information regarding your 15 Amp Router Speed Control, please refer to the warranty card included with your purchase or visit the official Harbor Freight Tools webサイト。保証条件は異なる場合があります。

カスタマーサポート:

If you require assistance, have questions about the product, or need to report a defect, please contact Harbor Freight Tools customer service. Contact information can typically be found on their official webサイトまたは購入領収書に記載されています。

一般的なお問い合わせは、 ハーバーフレイトツール webサイト.