TFA Dostmann 30.3139 Wireless Temperature Transmitter Instruction Manual

導入

This instruction manual provides essential information for the setup, operation, and maintenance of your TFA Dostmann 30.3139 Wireless Temperature Transmitter. This device is designed to wirelessly transmit temperature data to compatible TFA weather stations, including models 30.3033, 35.1057, 35.1058, 35.1066, 35.1071, and 35.1085. Please read this manual thoroughly before use to ensure proper functionality and longevity of the product.

製品終了view および機能

The TFA Dostmann 30.3139 is a digital temperature transmitter designed as a replacement or additional sensor for compatible TFA radio weather stations. It offers reliable wireless temperature transmission with the following key features:

• 互換性: Functions as a replacement or additional sensor for TFA radio weather stations 30.3033, 35.1057, 35.1058, 35.1066, 35.1071, and 35.1085.
• 拡張範囲: Provides a wireless transmission range of up to 100 meters (328 feet) in open field conditions.
• Cable Probe: Includes an additional cable probe for specialized temperature measurements, such as in water or soil, while the main unit remains protected.
• 柔軟な取り付け: Can be conveniently hung or placed on a flat surface. It is recommended to mount the unit in a location protected from direct precipitation.
• 統合ディスプレイ: Features a digital display showing the current temperature reading directly on the transmitter.

パッケージ内容

開梱したら、すべてのアイテムが揃っていることを確認してください。

• TFA Dostmann 30.3139 Wireless Temperature Transmitter
• Cable Probe (approximately 50 cm long)
• Batteries (quantity as specified on packaging, typically 2x AAA)

設定

1. バッテリーの取り付け

1. 送信機の背面にある電池ケースのカバーを開きます。
2. Insert the provided batteries, ensuring correct polarity (+/-).
3. 電池カバーをしっかりと閉じてください。

2. チャンネルの選択

Inside the battery compartment, locate the channel switch (usually labeled 1, 2, 3). If you are using multiple transmitters with one weather station, each transmitter must be set to a different channel. For a single transmitter, any channel can be selected.

3. ウェザーステーションとのペアリング

To establish a connection between the transmitter and your main weather station unit, follow these steps:

1. Remove all batteries from both the main weather station unit and all transmitters (including existing ones).
2. Ensure each transmitter is set to a unique channel (1, 2, or 3) using the switch in the battery compartment.
3. Reinsert batteries into all transmitters first.
4. Within approximately 2 minutes, reinsert batteries into the main weather station unit.
5. Allow a few minutes for the devices to synchronize. The temperature readings from the transmitter(s) should appear on your weather station display.

4. 送信機の取り付け

The transmitter can be mounted in two ways:

• ぶら下がっている： Use the hanging hole located on the top rear of the unit.
• 立ち位置: Utilize the foldable stand at the bottom for placement on a flat surface.

For optimal performance and longevity, position the transmitter in a location protected from direct sunlight, rain, and heavy snow. If using the cable probe, the main unit can be sheltered while the probe extends to the desired measurement area.

手術

ディスプレイを読む

The integrated digital display on the transmitter shows the current temperature being measured. If the cable probe is connected, the display will show the temperature from the cable probe. If the cable probe is not connected, it will show the internal temperature of the transmitter.

Using the Cable Probe

The cable probe extends the temperature sensing capability. Plug the cable probe into the designated port on the side of the transmitter. The probe can be placed in environments where the main unit cannot, such as in water, soil, or other specific locations, while the transmitter itself remains in a protected area. Ensure the probe tip is fully immersed or positioned correctly for accurate readings.

メンテナンス

クリーニング

To clean the transmitter, simply wipe it with a soft, damp 布で拭いてください。研磨剤入りの洗剤や溶剤は、表面を傷つける恐れがありますので使用しないでください。asing or display. Ensure the unit is dry before re-exposing it to outdoor conditions.

バッテリー交換

When the display on the transmitter or your main weather station indicates low battery, replace the batteries promptly. Refer to the "Battery Installation" section under Setup for instructions. Always replace all batteries at once with new ones of the same type.

最適な配置

Regularly check the placement of your transmitter. Ensure it remains protected from direct weather elements to prolong its lifespan. If using the cable probe, verify its position for continued accurate readings.

トラブルシューティング

No Temperature Reading on Weather Station

• バッテリーを確認してください: Ensure fresh batteries are correctly installed in both the transmitter and the main weather station unit.
• Re-synchronize: Perform the pairing procedure described in the "Setup" section (remove all batteries, reinsert into transmitters first, then main unit).
• チャネル競合: Verify that each transmitter is set to a unique channel (1, 2, or 3) if you are using multiple sensors.
• 範囲： Ensure the transmitter is within the 100-meter range of the weather station and that there are no significant obstructions (thick walls, large metal objects) that could interfere with the signal.

不正確な温度測定値

• 配置: Ensure the transmitter (or cable probe) is not in direct sunlight, near heat sources, or in areas with poor air circulation, which can affect readings.
• Cable Probe Connection: If using the cable probe, ensure it is securely plugged into the transmitter.
• 環境要因: Extreme weather conditions can sometimes temporarily affect sensor performance.

Transmitter Display Not Working

• 電池: 電池を新しいものと交換してください。
• ダメージ： ユニットに目に見える損傷がないか検査します。

仕様

保証とサポート

Spare parts for this product are generally available for a period of 1 year from the date of purchase. For technical support, warranty claims, or further inquiries, please contact TFA Dostmann customer service. Refer to the official TFA Dostmann webお住まいの地域の連絡先情報については、サイトまたは製品パッケージをご覧ください。