Corning PC-620D スターリングホットプレート ユーザーマニュアル

1. はじめに

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Corning PC-620D Stirring Hot Plate. The PC-620D is a laboratory instrument designed for precise temperature control and stirring of various solutions, featuring a durable Pyroceram top and digital displays for both temperature and stirring speed.

Figure 1: Corning PC-620D Stirring Hot Plate. This image shows the hot plate from an angled front view, highlighting the white Pyroceram top, the gray base, and the control panel with digital readouts for stirring speed (RPM) and temperature (Celsius), along with the 'Stir' and 'Heat' control knobs.

2. 安全情報

怪我や機器の損傷を防ぐために、常に次の安全上の注意事項を守ってください。

• 熱い表面： The top surface can reach high temperatures. Always allow the unit to cool completely before touching or moving. A "HOT TOP" indicator light will illuminate when the surface temperature exceeds 60°C (140°F).
• 電気安全: Connect the unit only to a properly grounded electrical outlet with the specified voltage (120V/60Hz). Do not operate with a damaged power cord.
• 換気： 過熱を防ぐために、ユニットの周囲に十分な換気を確保してください。
• こぼれ： In case of spills, immediately disconnect the power and clean the unit carefully after it has cooled. Avoid liquid ingress into the internal components.
• 個人用保護具: Always wear appropriate personal protective equipment (e.g., heat-resistant gloves, eye protection) when operating the hot plate.
• 使用目的: Use the hot plate only for its intended laboratory heating and stirring applications. Do not use for heating flammable or explosive materials without proper safety protocols.

3. 箱の中身

Upon unpacking, verify that the following item is present:

• One (1) Corning PC-620D Stirring Hot Plate

不足または破損しているコンポーネントがある場合は、直ちにサプライヤーに連絡してください。

4. セットアップ

1. 配置: Place the hot plate on a stable, level, and heat-resistant surface away from flammable materials. Ensure there is sufficient clearance around the unit for air circulation.
2. 電源接続: Connect the power cord to the back of the hot plate and then plug the three-prong plug into a grounded 120V/60Hz electrical outlet.
3. 初期検査: Before first use, inspect the unit for any visible damage from shipping.

5. 操作

5.1コントロールとインジケーター

• 電源インジケーター: Green light illuminates when the unit is powered on.
• STIR Knob: Controls the stirring speed from 60 to 1150 RPM. Turn clockwise to increase speed.
• STIR RPM Display: Digital LED display shows the current stirring speed in RPM.
• HEAT Knob: Controls the heating temperature from 5°C to 550°C. Turn clockwise to increase temperature.
• TEMPERATURE Display: Digital LED display shows the set temperature in Celsius. It blinks until the set temperature is reached.
• HOT TOPインジケーター: Red light illuminates when the top surface temperature exceeds 60°C (140°F), even if the heat function is turned off.

5.2 Stirring Function

1. Place a suitable stir bar into your vessel (e.g., beaker, flask) containing the solution.
2. Place the vessel centrally on the Pyroceram top.
3. Turn the STIR knob clockwise to the desired RPM. The digital display will show the set speed.
4. Adjust the speed as needed for optimal mixing without splashing.
5. To stop stirring, turn the STIR knob counter-clockwise to the "Off" position.

5.3 加熱機能

1. Place your vessel containing the sample on the Pyroceram top.
2. Turn the HEAT knob clockwise to the desired temperature. The digital display will show the set temperature in 5°C increments.
3. The temperature display will blink until the set temperature is reached, then it will remain steady.
4. Monitor the HOT TOP indicator. It will remain lit as long as the surface temperature is above 60°C, even after the heat is turned off.
5. To turn off heating, turn the HEAT knob counter-clockwise to the "Off" position. Allow the unit to cool down naturally.

6. メンテナンスとケア

• クリーニング： Disconnect the power cord and allow the unit to cool completely before cleaning. Wipe the Pyroceram top and housing with a damp 布と中性洗剤。 研磨剤や溶剤は使用しないでください。
• こぼれ： Clean spills immediately to prevent residue buildup. For chemical spills, refer to appropriate safety data sheets for cleaning procedures.
• ストレージ： ホットプレートは使用していないときは清潔で乾燥した環境に保管してください。
• 検査： 電源コードに損傷の兆候がないか定期的に点検してください。

7。 トラブルシューティング

8. 仕様

9. 保証とサポート

コーニングPC-620Dスターリングホットプレートには、 2年間保証 from the date of purchase, covering defects in materials and workmanship under normal use. For warranty claims, technical support, or service inquiries, please contact Corning customer service or your authorized distributor.

Please have your model number (6795-620D) and purchase information ready when contacting support.