SEM 38203 Black Guide Coat - 12 oz. Instruction Manual

1.製品オーバーview

The SEM 38203 Black Guide Coat is an aerosol product designed to assist in identifying surface imperfections on automotive bodywork prior to final painting. It provides a visual contrast that highlights low spots, sand scratches, and other minor flaws in primer or body filler, ensuring a smooth and uniform surface. Its quick-drying formula is engineered to prevent clogging of sandpaper during the sanding process.

Image 1: SEM 38203 Black Guide Coat aerosol can.

2. 安全情報

警告： This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65). Always read and follow all warnings and instructions on the product label before use.

• Use in a well-ventilated area. Avoid breathing vapors or spray mist.
• Wear appropriate personal protective equipment, including safety glasses, gloves, and a respirator if ventilation is inadequate.
• 熱、火花、裸火、高温の表面から遠ざけてください。禁煙。
• 加圧容器：使用後であっても、穴を開けたり、燃やしたりしないでください。
• Do not expose to temperatures exceeding 50°C/122°F.
• お子様やペットの手の届かない場所に保管してください。
• 目に入った場合は、すぐに大量の水で洗い流し、医師の診察を受けてください。
• In case of contact with skin, wash immediately with soap and water.

3. 準備

1. Ensure the surface to be coated is clean, dry, and free of dust, grease, oil, and other contaminants.
2. ミキシングボールがカタカタと音を立て始めたら、少なくとも1分間、エアゾール缶を勢いよく振ってください。使用中も時々振ってください。
3. Test spray on an inconspicuous area or a test panel to ensure proper spray pattern and color.

4. 申請手順

Apply the Black Guide Coat to the primed or body-filled surface using the following steps:

• 缶を表面から約8〜10インチ（20〜25cm）離して持ちます。
• Apply a light, even mist coat over the entire area to be sanded. The goal is to create a thin, uniform black layer. Avoid heavy application, as this can obscure minor imperfections.
• Allow the guide coat to dry completely. The formula is quick-drying, typically within a few minutes, but drying times may vary based on temperature and humidity.
• Once dry, begin sanding the surface. The black guide coat will be removed from the high spots first, leaving black in the low spots, pinholes, and sand scratches. This visual contrast clearly indicates areas that require further sanding or filling to achieve a perfectly flat surface.
• Continue sanding until all black guide coat is removed, indicating a uniform and smooth surface. The non-clogging formula helps maintain abrasive efficiency.

5. 保管とメンテナンス

• Store the aerosol can in a cool, dry, well-ventilated area, away from direct sunlight and heat sources.
• 120°F (49°C) を超える温度で保管しないでください。
• After each use, invert the can and spray for a few seconds to clear the nozzle, preventing clogs for future use.
• Dispose of empty cans according to local regulations.

6。 トラブルシューティング

• 不均一な塗布： Ensure the can is shaken thoroughly before and during use. Maintain a consistent distance and speed while spraying.
• ノズル詰まり: If the nozzle clogs, remove it and clean with a suitable solvent. Replace if necessary. Always clear the nozzle after use by inverting the can and spraying.
• Guide Coat Not Highlighting Imperfections: Ensure the application is a light mist. A heavy coat can fill in minor imperfections, making them harder to detect.

7. 製品仕様

8. 保証とサポート

For specific warranty information or technical support regarding the SEM 38203 Black Guide Coat, please refer to the product packaging or contact SEM customer service directly. Contact details are typically available on the manufacturer's official website or product label.

Note: The provided product data does not include specific warranty terms or direct support contact information.