DeVilbiss 802342 スターティングライン HVLP 重力式スプレーガンキット ユーザーマニュアル

導入

The DeVilbiss 802342 StartingLine HVLP Gravity Spray Gun Kit is a comprehensive system designed for auto painting and touch-up applications. This kit includes a full-size HVLP spray gun with a 1.3mm fluid tip, a mini HVLP detail gun with a 1.0mm fluid tip, an air adjusting valve, and a 1.8mm primer set-up. All components are conveniently organized within a durable molded case, providing a complete solution for various painting needs.

安全情報

Always prioritize safety when operating spray painting equipment. Failure to follow safety guidelines can result in serious injury or property damage.

• 換気： Use in a well-ventilated area to prevent the accumulation of hazardous fumes. If adequate ventilation is not available, use appropriate respiratory protection.
• 個人用保護具（PPE）： Always wear appropriate PPE, including safety glasses or goggles, gloves, and a respirator suitable for paint fumes.
• 可燃性物質: Many paints and solvents are flammable. Keep away from open flames, sparks, and other ignition sources. Do not smoke while operating the spray gun.
• 圧力安全性: Never exceed the maximum recommended air pressure for the spray gun. Always release air pressure from the system before performing maintenance or cleaning.
• 化学物質への暴露: この製品を使用すると、カリフォルニア州でがんや先天異常、その他の生殖障害を引き起こすことが知られている鉛などの化学物質にさらされる可能性があります。詳細については、 www.p65warnings.ca.gov.
• 電気安全: Ensure all electrical connections for air compressors or other equipment are properly grounded and in good condition.
• 子供とペット: Keep children and pets away from the work area and equipment.

製品終了view およびコンポーネント

The DeVilbiss 802342 kit provides a versatile set of tools for various painting tasks. Familiarize yourself with the components before use.

Figure 1: DeVilbiss 802342 StartingLine HVLP Gravity Spray Gun Kit, showing the full-size HVLP spray gun, mini HVLP detail gun, air adjusting valve, and various cleaning accessories neatly organized in a molded case.

Figure 2: Contents of the DeVilbiss StartingLine Spray Gun Kit, including two spray guns, fluid cups, and cleaning tools.

図3: 別の view of the DeVilbiss StartingLine Spray Gun Kit components, highlighting the full-size and mini spray guns along with accessories.

キット内容:

• Full-Size HVLP Gravity Spray Gun: Equipped with a 1.3mm fluid tip, suitable for general painting applications.
• Mini HVLP Detail Gun: Features a 1.0mm fluid tip, ideal for touch-ups and fine detail work.
• Air Adjusting Valve: For precise control over air pressure at the gun.
• 1.8mm Primer Set-up: An additional fluid tip and needle for spraying thicker materials like primers.
• Molded Case: Provides organized storage and protection for the kit components.
• クリーニング用アクセサリ: Various brushes and tools for proper maintenance.

設定

1. コンポーネントを解凍します: Carefully remove all items from the molded case and inspect for any damage.
2. Select Fluid Tip: Choose the appropriate fluid tip (1.0mm, 1.3mm, or 1.8mm) based on the viscosity of the material you intend to spray. Ensure the corresponding needle and air cap are installed.
3. Attach Fluid Cup: Securely attach the gravity-feed fluid cup to the top of the spray gun.
4. 空気供給を接続する: Connect the air adjusting valve to the spray gun's air inlet, then connect your air hose from the compressor to the air adjusting valve. Ensure all connections are tight to prevent air leaks.
5. 初期クリーニング: Before first use, clean the spray gun thoroughly with an appropriate cleaning solvent to remove any manufacturing residues.

操作手順

1. 材料を準備します: Mix and thin your paint or coating material according to the manufacturer's instructions. Strain the material to remove any particles that could clog the gun.
2. Fill Fluid Cup: Pour the prepared material into the gravity-feed fluid cup. Do not overfill.
3. 空気圧の設定: With the air adjusting valve, set the air pressure at the gun to the recommended PSI for your material. For HVLP guns, this is typically between 10-30 PSI (Maximum Pressure: 30 PSI).
4. スプレーパターンを調整する:
   • Fan Control Knob: Adjust this knob to change the width of the spray pattern, from a narrow round pattern to a wide fan.
   • 流体制御ノブ: Controls the amount of material flowing through the gun. Turn clockwise to decrease flow, counter-clockwise to increase.
5. テストスプレー: Always perform a test spray on a piece of scrap material to verify the spray pattern and material atomization before applying to your actual workpiece. Adjust settings as needed.
6. スプレー技術：
   • 表面から一定の距離（通常は6〜8インチ）を保ってください。
   • Move the gun at a steady, even speed, overlapping each pass by about 50%.
   • Trigger the gun fully at the beginning of each pass and release at the end to avoid excessive material buildup.

メンテナンス

Proper cleaning and maintenance are essential for the longevity and optimal performance of your spray guns.

1. 即時清掃： Clean the spray gun immediately after each use. Do not allow paint to dry inside the gun.
2. 空の液体カップ: Empty any remaining material from the fluid cup.
3. Flush Gun: Pour a small amount of appropriate cleaning solvent into the cup and spray it through the gun until clear solvent emerges.
4. 分解して清掃する:
   • Remove the air cap, fluid tip, and needle.
   • Use the provided cleaning brushes and solvent to thoroughly clean all internal and external parts. Pay special attention to the air cap holes and fluid passages.
   • Do not use metal objects to clean the fluid tip or air cap holes, as this can damage them.
5. 潤滑: Lightly lubricate the needle packing and air valve packing with a non-silicone lubricant designed for spray guns.
6. 再組み立てと保管: Reassemble the gun carefully. Store the clean and dry spray gun in its molded case to protect it from dust and damage.

トラブルシューティング

このセクションでは、発生する可能性のある一般的な問題を取り上げ、考えられる解決策を示します。

仕様

保証とサポート

For detailed warranty information, technical support, or to purchase replacement parts, please refer to the official DeVilbiss webサイトにアクセスするか、カスタマーサービスにお問い合わせください。

An official Installation Manual (PDF) is available for further reference:

• インストールマニュアル（PDF）をダウンロード