導入
The Emerson F145-1328 Indoor Remote Sensor is designed to enhance the temperature monitoring capabilities of compatible Emerson Blue and White-Rodgers thermostats. This wired sensor provides accurate indoor temperature readings from a location separate from the main thermostat, allowing for improved climate control within your space.
安全情報
- Always disconnect power to the thermostat and HVAC system before installation or servicing to prevent electrical shock.
- すべての配線接続が安全であり、地域の電気規則に準拠していることを確認してください。
- Do not install the sensor in locations exposed to direct sunlight, drafts, or near heat-generating appliances, as this can affect temperature accuracy.
- デバイスを乾燥した状態に保ち、湿気を避けてください。
パッケージ内容
パッケージに次のアイテムが含まれていることを確認してください。
- Emerson F145-1328 Indoor Remote Sensor
- インストールガイド（このドキュメント）
- Mounting hardware (screws, wall anchors - may vary)
画像1：正面 view of the Emerson F145-1328 Indoor Remote Sensor.
セットアップとインストール
1. 互換性
This remote sensor is compatible with Emerson Blue and White-Rodgers thermostats that feature a wired indoor remote sensor option. Refer to your thermostat's manual to confirm compatibility.
2.センサーの配置
Select a suitable location for the sensor that accurately represents the temperature of the area you wish to monitor. Avoid placing the sensor:
- Near windows or doors where drafts may occur.
- 直射日光の当たる場所。
- Near heat sources such as lamps, televisions, or heating vents.
- On exterior walls.
The maximum recommended distance from the thermostat is 300 feet (approximately 91 meters). For optimal performance, keep the wiring run as direct as possible.
Image 2: The remote sensor shown with approximate dimensions for placement reference.
3.配線手順
The F145-1328 is a wired sensor and typically requires three wires for connection to the compatible thermostat. Consult your thermostat's installation manual for specific wiring terminal designations (e.g., S1, S2, S3 or similar). The sensor connects to these dedicated remote sensor terminals.
- 電源を切る： Before beginning, turn off power to your HVAC system at the circuit breaker.
- Access Thermostat Wiring: Carefully remove the cover of your thermostat to access the wiring terminals.
- ワイヤーを接続する: Connect the three wires from the remote sensor to the corresponding remote sensor terminals on your thermostat. Ensure connections are tight.
- マウントセンサー： Secure the remote sensor to the wall using the provided mounting hardware.
- 電力を回復する： Once all connections are secure and the sensor is mounted, restore power to your HVAC system.
- Configure Thermostat: Follow your thermostat's instructions to enable and configure the remote sensor. This may involve navigating through the thermostat's menu to select the remote sensor option.
Note: Wiring color codes may vary. Always refer to the wiring diagram provided with your specific thermostat model.
操作手順
Once properly installed and configured, the F145-1328 remote sensor will automatically provide temperature data to your compatible Emerson or White-Rodgers thermostat. The thermostat will then use this digital signal for more precise temperature monitoring and control.
- 温度監視: The thermostat will display the temperature reported by the remote sensor, or an average if multiple sensors are used.
- 精度の向上: The digital signal from the sensor contributes to a more accurate and stable temperature reading compared to the thermostat's internal sensor alone, especially if the thermostat is in a less ideal location.
- システム応答: The HVAC system will respond to the temperature data from the remote sensor, helping to maintain the desired climate in the monitored area.
メンテナンス
The Emerson F145-1328 Indoor Remote Sensor requires minimal maintenance.
- クリーニング： Periodically wipe the exterior of the sensor with a soft, dry cloth to remove dust. Do not use liquid cleaners or abrasive materials.
- 障害物チェック: Ensure that the sensor is not obstructed by furniture, curtains, or other objects that could block airflow and affect temperature readings.
トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Sensor not detected by thermostat. | Incorrect wiring, loose connections, thermostat not configured for remote sensor, incompatible thermostat. |
|
| 温度の測定値が不正確です。 | Improper sensor placement (direct sunlight, drafts, heat sources), sensor malfunction. |
|
| 断続的な読み取り。 | Loose wiring connections, excessive wire length, electrical interference. |
|
仕様
- モデル： F145-1328
- 互換性: Emerson Blue and White-Rodgers thermostats with wired indoor remote sensor option
- センサータイプ: 有線
- 最大ワイヤ長: 300フィート（約91メートル）
- 寸法: 約1.88 x 3.38 x 4インチ（4.78 x 8.59 x 10.16 cm）
- 重さ： 約2.4オンス（68グラム）
- 電源: Powered by thermostat (no batteries required)
- 含まれるコンポーネント: 製品と説明書ガイド
保証とサポート
For warranty information and technical support, please refer to the documentation provided with your primary Emerson or White-Rodgers thermostat, or visit the official Emerson webサイト。 保証請求に備えて購入時のレシートを保管しておいてください。
エマーソンカスタマーサポート: www.emerson.com/en-us/contact-us