Presto EverSharp Electric Knife Sharpener (Model 08800) User Manual

導入

The Presto EverSharp Electric Knife Sharpener (Model 08800) provides an efficient and automatic method for sharpening most non-serrated kitchen and sport knives. This two-stage system is designed to precision grind a perfect sharpening angle and then fine hone and polish the edge, delivering professional results for home use.

図1: 前面 view of the Presto EverSharp Electric Knife Sharpener.

重要な安全対策

電気製品を使用するときは、火災、感電、人への傷害のリスクを軽減するために、次のような基本的な安全上の注意事項に常に従う必要があります。

• シャープナーを使用する前に、すべての説明書をお読みください。
• To protect against electrical hazards, do not immerse the sharpener in water or other liquids.
• 使用しないとき、部品の取り付けや取り外しの前、および清掃の前には、必ずコンセントからプラグを抜いてください。
• 可動部品との接触を避けてください。
• コードやプラグが損傷した状態で、またはアプライアンスが故障したり、何らかの方法で落下または損傷した後は、アプライアンスを操作しないでください。検査、修理、または電気的または機械的調整のために、アプライアンスを最寄りの認定サービス施設に返却してください。
• 機器メーカーが推奨または販売していないアタッチメントを使用すると、火災、感電、またはけがの原因となる可能性があります。
• 屋外では使用しないでください。
• コードをテーブルやカウンターの端から垂らしたり、熱い表面に触れたりしないでください。
• この機器は家庭用としてのみご使用いただけます。
• Always ensure the sharpener is placed on a stable, flat surface before use. The non-slip base helps secure the unit during operation.

設定

1. Unpack the knife sharpener and place it on a clean, dry, and stable countertop.
2. Ensure the power switch is in the "OFF" (O) position.
3. 電源コードを標準の120ボルトACコンセントに差し込みます。
4. Verify the non-slip suction cups on the base are securely attached to the countertop to prevent movement during sharpening.

図2：下 view of the sharpener, highlighting the non-slip suction cups for stability.

操作手順

The Presto EverSharp features a two-stage sharpening system. Stage 1 is for precision grinding, and Stage 2 is for fine honing and polishing. Always sharpen non-serrated knives. For serrated knives, refer to the specific instructions below.

Sharpening Non-Serrated Knives

1. Turn the sharpener ON by pressing the power switch to the "I" position. The sharpening wheels will begin to rotate.
2. Stage 1 - Coarse Sharpening: Insert the knife blade into the left slot of Stage 1 (marked '1'). Hold the knife with the blade perpendicular to the sharpener and pull it towards you with light, even pressure. The precision blade guides will automatically position the knife at the ideal sharpening angle.
3. Repeat this process 3-4 times for each side of the blade, alternating between the left and right slots of Stage 1. Ensure you pull the entire length of the blade through the slot, from heel to tip.
4. Stage 2 - Fine Honing: Sに移動tage 2 (marked '2'). Insert the knife blade into the left slot of Stage 2. Again, pull the knife towards you with very light pressure, allowing the Sapphirite wheels to fine hone and polish the edge.
5. Repeat this 3-4 times for each side of the blade, alternating between the left and right slots of Stage 2. このstage refines the edge for a razor-sharp finish.
6. After sharpening, turn the sharpener OFF (O) and carefully wipe the blade with a damp 布で金属粉を取り除きます。

Figure 3: Demonstrating how to hold and guide a knife through the sharpening slot.

Figure 4: Close-up of the power switch, indicating ON/OFF positions.

鋸歯状のナイフを研ぐ

This sharpener can be used for non-electric serrated knives that are only serrated on one side. For these knives, only use Stage 2 (fine honing) and only sharpen the non-serrated side of the blade. Do not attempt to sharpen the serrated edge.

1. Turn the sharpener ON.
2. Insert the non-serrated side of the blade into the appropriate slot of Stage 2 (marked '2').
3. Pull the knife towards you with light pressure, ensuring only the non-serrated edge makes contact with the sharpening wheel.
4. 3〜4回繰り返します。
5. Turn the sharpener OFF and clean the blade.

役立つヒント

• Always use light pressure. Excessive pressure can slow the motor and damage the blade.
• Maintain a consistent speed when pulling the knife through the slots.
• For very dull knives, you may need additional passes through Stage 1 before moving to Stagと2。
• Sparks may occur when sharpening high carbon steel knives; this is normal.

メンテナンスと清掃

Regular cleaning ensures optimal performance and longevity of your sharpener.

1. 清掃する前に必ずシャープナーのプラグを抜いてください。
2. Wipe the exterior of the sharpener with a damp 布。本体を水に浸さないでください。
3. The sharpener is equipped with receptacles underneath to catch metal filings. To clean, remove the red plugs on the bottom of the unit and empty the filings. Replace the plugs securely after cleaning.
4. Do not attempt to lubricate the sharpening wheels or any other part of the sharpener.

トラブルシューティング

• シャープナーがオンにならない: Ensure the power cord is securely plugged into a working electrical outlet and the power switch is in the "I" (ON) position.
• Knife not sharpening effectively:
  • Ensure you are using light, consistent pressure. Too much pressure can hinder sharpening.
  • Verify you are pulling the knife through the correct slots for Stage 1 と Stagと2。
  • For very dull knives, more passes through Stage 1 が必要になる場合があります。
  • Ensure the knife is non-serrated, or if serrated, only the non-serrated side is being sharpened in Stagと2。
• Excessive sparks: While normal for high carbon steel, ensure you are not applying excessive downward pressure.

仕様

保証とサポート

The Presto EverSharp Electric Knife Sharpener (Model 08800) comes with a 1-year limited warranty against defects. For warranty claims or product support, please refer to the contact information provided in your product packaging or visit the official Presto webサイト。